Recent content by Josh40601

Hey guys, I am having a problem finding a lower radiator hose that works. The lower radiator hose and the power steering box want to take up the same location. I currently have a hacked up hose with a piece of galvanized pipe and a bunch of hose clamps right now, but after driving around for...

Hello everyone, I have to add O2 sensors to my truck and I need to know where they were located from the factory, but I also think I may have problem with my current exhaust setup. I found some info in this thread http://www.explorerforum.com/forums/showthread.php?t=320348&page=3 when the...

So engine codes and running like shit usually go together, but here is what I have coming up. I spoke to the tuner yesterday and he basically said, "with a stock motor, stock MAF, stock ECU, it should run fine." Well, it doesn't. still does that stupid "camming" shitty idle crap after it...

Bumper version 2

Still got that bro lean, but close enough. I'll likely just use a shorter spring up front and call it a day. Been working on my buddies 97 that we did an 06 conversion on and trying to get his bumper lined up. He went with the same bumper D had.

Parts didn't come in. So I put the shocks back together and finished up the engine bay. Definitely has that lean that I'm not keen on. It does have about 300lbs of shit in the bed but it's still wayyyyy too low in the back. This is level. I'm hoping it settles as id like it about an inch...

Last two days were all about rebuilding the hubs brakes and bearings. After cleaning or replacing everything, the axle shafts won't go into the lockouts. I'll deal with it after paint. Coilovers off, springs going on tomorrow, tune up, and off to the body shop

Gotta a question about my sploder (this issue is with parts that are the same on the Ranger)... So I can't get my 4x4 working. Shift motor replaced, metered everything and found some wires that didn't have voltage. If looking at the shift computer, there are 2 plugs on the left that plug...

Anyone have a wiring diagram or wire color list and what each wire does for a 2001 3.0 non-flex fuel truck? I have alldata, but no diagram showing what each of the different color wires are going to. Any help would be greatly appreciated.

Ok, so I have been searching online and around Lexington for a place to buy metal at a good price. I checked Metal Supermarket and they are way too pricey for me, so I have been looking elsewhere... I'm mainly concerned with cost of tube. I'm looking at 3 different metals.. 1) schedule 40 pipe...

Hey gents (and ladies), i am trying to find a cheaper (price) replacement for the door jam switch. The part number i have is Motorcraft SW5429B. This is for the right rear door to a 2002 Ford F250 Crew cab. I know this isn't a ranger, but it is a Ford, and i know you all are very familiar with...

A lot of people from this forum and others have been asking a lot about the swap I did on my yellow truck. I had created a thread a long time ago about it, but I don't know where it is nor do I know where the original pics are. Here is the link to the online magazine article that gives an...

So i am trying to find out what the actual normal temp is, what is "getting purty warm" and "Shut it the F off!!" temps are for the 4.0 in my Explorer. With my Efans running, i usually run around 190*, with them off, i run around 205-210. Hope you guys can help. Sorry if it is a double post...

truck looks great brother. You don't have any issues with your tierod hitting the Ballistic cover? I couldnt install mine on D because i hit the cover about a 1/4 turn before lock i hit it with the Tirod.

Alright, so i have had 2 different CBs. One is a Cobra Limited Edition Army version. (I don't know the model number) I bought it brand new in March. It worked great for a while, then suddenly, no sound. People can hear me for miles, but i can't hear anyone. I can litterely be parked right next...