Recent content by rochhound

im replacing my oxy sensor,the plug that goes up to the engine is damaged i cant seem to find a replacement anyone know where i can find a relacement thanks steve

thanks guys so the sensor in the diferential is for abs,and the sensor on the speedometer is for cruise control trying to reconnect the cruise control this thing is now ticket getter! thanks again

i got rid of my 2.9 eng put in a 4.0 explorer motor ,kept my 88 alrd trans (was rebuilt) wiring was challenging,every thing else went well love the extra power! wiring 1 theres a sensor in the rear end with a blue and green wire what does this sensor control? 2 theres a sensor on the...

ive installed my 91 exp 4.0 used my 88 al4d was just rebuilt. i tested it today and no overdrive ,can some direct me to a trouble shooting or wiring diagram. ive connected all the trans wiring from the 91 exp all the plugs but the schematics i have doesnt show enough? any appreciated steve

i have a 1988 bronco II 2.9,im putting in a 1991 4.0 my question is about trans missions. my 88 bronco II has a fresh automatic trans rebuild in it. Can it be used with the 4.0? the doner explorer trans doesnt lock up in high gear not sure why. any help appreiated steve

i have a 1988 ford bronco II 2.9 i have engine code 64 (air intake temperature signal low) when its cold idle is very low after warming up code goes away and idles ok my question is what componet or part is causing the problem? thanks steve

im getting ready to tune my 2.9 up want to buy the best plugs for this? your opinion thanks steve

picked up a 88 b2 cracked head,replaced with 89 heads runs great. my problem is the temp guage go's to hot when the motor is just barely warm. i changed the sensor but still gives hot temp at guage? could the guage in dash be bad?

any one have a copy of a schematic for a 94 explorer i have installed a 94 and im having problems with codes 56 66 mass air need to trace wiring. thanks steve

my 88b2 has a 4.0 motor in it i installed a couple of years ago. i read my computer and i have quite a few code errors. ive looked them up but dont understand what they mean,im looking for more info on what they mean and what part is involved. the codes are #27,29.32,56,66,93. for instance code...

i have a 1988 bronco II with dana 35 front end with jeep limited slip ,0 lift love it! my question is what year front shock should i use 1988 or 1994 when i shop there different, im guessin at 1990 to 94 thats the years for the dana 35. your opinion appreciated. thanks steve

i have a 1993 explorer 8.8 rear end for my broncoII i want to change the ring@pinion to 4.10 ratio.will a 1998 explorer 8.8 ring and pinion fit in a 1993 rear end looking at one on ebay. thanks steve

my bronco II has a 4.0 i put in a while back . im having a problem with the fan hitting the shroud and breaking the fan blades when im putting high torgue like a steep hill 4 wheeling. im using the 4.0 shroud and radiator. i used the stock 2.9 motor mounts! i obviously need to change these...

i have 86 b2 and i cant figure what this is or does ,when i took it apart it looks like it should have a filter in it.the reason im asking is i drove it on a 300 mile trip ran great, but on the way home it started acting like it was running out of gas. as long as i kept it below 6o mph it...

will a 84 bronco II c5 from a 2.8 bolt to a 2.9 0r 4.0 i have one and ive heard there a lot stronger than a4ld's your opinion would be appreciated. thanks