Search results

Yeah I need to do more inspect/diagnosis but when i do eventually (regardless) replace the radius arm I will make a vid or pictorial how to

Correct assumption lol thanks for the link!

Oh I forgot to add: 1992 125" wheelbase 4x4 TTB with Dana 35

A few years back I replaced all the rubber in my front end with poly when I rebuilt my front axles. I found a small rub wear point where the radius arm meets the mounting bracket on the truck's frame. Then she had motor problems and had to sit while I used a commuter trying to save up for...

Hey y'all, Any meetups or off road clubs for Colorado folks? Would love to get my Ranger back out in the mountains - she needs a radius arm so not fully up to par but I can do greens and mild blues on trail ratings. Love camping, fishing, climbing, skiing, and mountaineering and would love get...

Hey y'all, I installed a new electric cooling fan system with a thermostat controlled activator. I am adding a relay into the system to help reduce electrical load, but also to incorporate a signal circuit from the A/C pressure switch. I have a 1992 4.0L with the factory A/C installed. All...

Hey @gaz Thank you for the recommendation. Is that model from Summit racing an exact fit or do I need to prepare to do some modifications to get it mounted properly? Thx - rangergirl92

Okay everyone, first I wanted to thank you all for your recommendations and insight - it has been very helpful in reassessing nad finding the right parts for this upgrade! I have decided to do the following: I am picking up a 16" 8-blade fan with a 3000 CFM max output for $50. I can easily...

Hey thank you for the information and clarifications. I made a mistake it is actually a 13" 8 blade fan kit: https://www.lmctruck.com/1983-11-ford/cooling-system/fr-electric-cooling-fan So could I get little "L" brackets to adapt the factory shroud then? Where can I find such brackets? Hardware...

CORRECTION: it is a 13" 8 blade fan kit from LMC truck. I bought the thermostat as well. It has an output of 1560CFM.

It was a kit I got from LMC truck's website. The fan is 13",8 blades with an output of 1560CFM https://www.lmctruck.com/1983-11-ford/cooling-system/fr-electric-cooling-fan

I bought an electric cooling fan from LMC truck to take load off the motor and improve hp, mpg, torque. I got all those benefits and they were better than id hoped! But the motor gets up there in temps now. She's a 92 so the gauge has L to H with a "normal" range. Sits fine on highway. A/C...

Hi all, So I have been desperately searching for the oil level sensor connector for my 4.0L OHV but it's almost impossible to find. I know its a discontinued part and all that noise so yeah. OE Motorcraft part numbers: WPT-237 or 3U2Z-14S411-TA Any suggestions on where to find a new one...

Hey Ron, Thanks for the information, this was very helpful!!

I am lookimg to replace the single pane rear slider with a double pane rear slider in my 92 super cab. LMC truck has a double panel slider that comes pre-tinted: https://www.lmctruck.com/1983-11-ford/fr-1983-11-sliding-rear-window Only thing is, they are saying that the super cab model has to...

I am looking to do the same thing to my 92 super cab. LMC truck has a double panel slider that comes pre-tinted: https://www.lmctruck.com/1983-11-ford/fr-1983-11-sliding-rear-window Only thing is, they are saying that the super cab model has to be replaced with a urethane adhesive.... Now I...

Hello! I bought a set of Hedman headers for my Ranger and they fit and all is kosher there - there is one additional O2 port on the driver side and another port for additional emission control monitoring devices on the passenger header pipe. My truck is older with an OBDI system so there is...

I did not think to do that - I think I might be able to barter a YouTube promotional video ( I am a videographer as a side hustle) for an exhaust shop in town in exchange for a fat discount - thank you for the tip! No - when I searched their website, the term "exhaust studs", or "exhaust stud...

Thank you! So how long do they need to be at M8x1.25? Yes I found the grade 8.8 on Grainger's website - but there are like 15 different lengths - obviously I don't need one that is 10 inches lol - but yeah just want to get everything in order before I start the install.

I have replace one of the exhaust manifolds maybe 6 years ago when it cracked. The nuts and studs that mount them to the block are in decent shape despite their age. I recently bought an entire new exhaust system, Hedman Headers, a Magnaflow Cat, and am still piecing the catback system together...