Search results

I am breaking down on the drag truck project and buying aluminum heads, custom manifolds. My donor engine is a 2001 Explorer engine that left the road at 51000 miles in 2005 and was stored since. heads are still on block. Valve covers not removed yet. $400 plus shipping what you get: valve...

Please and thank you. PM with what you have available. Factory installed AC bracket, not any aftermarket parts please.

Following up on 6000 miles after “resurrection” of the 2001 Explorer 5.0 Wife’s uncle in Louisiana is passing, like in hours or days. Made a 1000 mile round trip leaving Sunday and coming home tonight to say goodbye. Most economical, most comfortable car is still the 2001 Exploder 5.0 with now...

1998 f150, 4.6, 185k. Oil consumption is virtually nil (max half quart per 5k mile oil change owned since 71k, proper oil changes, commuter driven. slick 50 or similar run every 3rd oil change since 100k. Biggest problem was coke buildup in egr circuits. Complete obstruction. Engine still...

I might have an interest in the 3.96 R&P leftovers if I’m good condition. Remington115, please pm me if you would and let me know what your plans are for the gear set.

Yes 2wd

Torino ends ONLY match 97-01 Explorer 5.0, 31 spline rear ends. It is a unique situation. All conversation on this subject pertains only to the 97-01 5.0L explorer rear end. If comparing to any other explorer rear, it’s an error. Strange, QP, Moser all sell late Torino new model ends...

Don, thanks for the reply. Not in a particular order: Yes torino F9 inch big bearing ends being added, their offset/change in housing length per side would be factored into the shortening/removal of housing material. Its moot. Washes out in the shortening process and isnt worthy of factoring...

picture attached

Work and life have prohbited me form spending much of any time on my v8 ranger project. Today was good, I got to mock hang my Explorer 8.8 (31 spline) with the actual tires and wheels. I need to get ride height correct as the truck is getting an MII front end and the ride height must be set at...

Second on Rock Auto for that engine.

I have a NIB 7.5 Trac Loc clutch pack avail for sale. If you are planning to freshen your 7.5 TL clutch stack, please reach out. Heretofore If I have a 7.5 that needs posi, Ill be adding a mini spool instead. I also have ball joints and front suspension parts (energy bushings), I uncovered a...

JerrySab, I expect your either after the "windshield" wiper gear train inside the cowl or the electric wiper switch. But you didnt say switch so I am expecting machine parts, from motor to wiper blade. In any case, wipers are ready for deletion on this cab and Im happy to send pics. if your...

1990 Frankentruck Bastardized by a resident of Mississippi before me. De-bastardized as best possible after acquisition. 2.3, OE everything. Dual plug. No AC (ala Bubba) Unknown gear, haven’t serviced the carrier yet) 5sp Very high mileage JYD replacement engine, 87 octane, religiously gets 22...

if you still need this, I have one. PM me Mike

Bobber64, how is the firewall for rust?? I need some firewall sections for rust repair on the 87 drag truck.(The one you asked about column shifter avail). You may not have interest in cutting it up..... but I also need some floor sections For a 1990 (Frankentruck). I have some rust from a...

Bobber64, that year is floor shifted. I have the whole shifter but …… it’s the OG floor unit. Nice condition.

Follow up on car. Windshield I installed (Chinese junk that I was stuck with due to supply issues)- leaked at top in front of passenger. There was rust abatement and repair prior to install. Several bad Bubba windows before me destroyed the pinch weld. My repairs weregood but the Chinese glass...

I was planning on just shortening the axle as most do and retain c-clips. I then found that my tire/wheel and aesthetics are not going to work at 56.75 inch width. I must knock an added 5-6 inch off. So new axles. New axles??? Do I keep c-clips and stay away from the sanctioned tracks? Do I buy...

For my 87 v8 project I am machining the bearing replacement bushings for narrowing the Explorer disc 8.8. I need to tuck deeply a set of 275 tires on 8s into the bed. This would be a limited use system ala Mittler Bros, using 1.5 TGP bar at only 65 inch and inner carrier and outer Big Ford/New...