Search results

I use to frequent this page a ton, but my life has went a different direction and now I'm building datsuns. Question is this. I'm needing a serpentine crank pulley for my Datsun L20b engine. I've been told pinto pulleys and other fords have the same pattern. Can anyone help me out on the...

I'm wiring all new turn signals. Pics to come. But what I'm not sure about is my wiring. Using a three terminal on off on switch. The middle terminal is 12+ ya? With a flasher in the middle. Then one side gets split to each turn signal for that side. And each turn signal grounded at the signal?

a bit too clean for me, but sick anyways http://www.racingjunk.com/category/1125/Other/post/1983087/1987-Bronco-II-Prerunner-Project-Truck.html?imageIndex=2&showSuperSize=true

i'm really seriously looking at a 77 280z. if ya got a carfax open, i'd be interested in knowing where the car has been! let me know!

got me some 35's! now i gotta get to building my 35/44 setup. heres a quick spec sheet, more info can be found on my buid thread 86 b2. chopped prerunner fenders up front 8.8 expo rear end chevy 64in leafs reverse 7in shackles jeep 5.5 lift coils up front custom stonecrusher style steering...

i was thinking of moving my TTB forward some when i finish building my 35/44. looks like the easiest way would be to have another engine craddle and put it in front of the stock craddle. then drill the passenger frame rail for the drop bracket. only thing else i can see that one would need to...

i got a new set of beams a few days ago. they were already fit with 44 knuckles. however, i still need the hubs, bearings, stud shafts, rotors calipers etc. so what vehicle am i looking for when i go to buy the parts? does it have to be a ttb44 or a solid 44 as well? i know its been talked...

I got on one knee last nite at sunset and asked my girlfriend of almost 5 years. we don't have a date set, but it will prob be around march of next year.

hello all, i'm gonna start building my steering soon. going with the stonecrusher idea. gonna use 1.5 .250 wall dom. and thinking of hiems. tho TRE's is an option as well. either way i go, i was thinking of running a 7/8 shank, should fit nicely in the 1.5 dom. is this needed? if i go hiem's...

i've got an old awooga horn hooked up to my b2. but it spools up real quick. and i'd like to slow it down a bit, more like an old firetrucks horn. how can i go about this? maybe a certain resistor or something?

hey guys, bought a another 1350m to swap for my fried one. but i didn't see how the driveshaft yoke comes apart from the 1350. it does slip like a slip yoke, but won't slide all the way off to install on my new 1350 also, will the stock driveshaft limit my flex when i start maxing the stock 28...

i have a m50d with a manual 1350 in my b2. i've noticed some whinning for a month or so, but i assumed it was the throw out bearing yelling at me. it drove fine last nite, both in 2wd from work, and then in 4x4 for some light wheeling. then this morning i pulled it outta the drive way and its...

i'm looking into some other coil's to use. read the tech library about the jeep rancho 6423's. and those have 240 ppi. saw some on rustysoffroad that look tempting, but they are labeled as 150 lb spring rate same thing but different wording? thoughts?

i feel like i'm missing something here. help me out? i'm wiring two 100w lights. everything is with 12g wire. so i hooked the positives together and ran them up to my relay at number 87. then hooked the negitives from the lights to the radiator core support (i know its a good ground, used it...

hey i work at napa and noticed that we sell some hella head light conversions. my book doesn't say much but that it replaces a sealed beam headlight and blah blah blah. anyone ever heard of it? i'll look deeper into it tomorrow if things slow a bit

not sure if we have a thread like this, but i thought it might be cool to have ppl measure the flex. the most accurate way would be with a measuring tape under the wheel on a ramp or something similar. i used a tractor and got 23in of clearance out of the front left, and 21in out of the back...

been working on my 1.5 year old boxer. she is getting good.

hey guys, so i have been reading up on ppl that have built their own radius arms. one thread (don't remember the OP) said to use 2in dom .25 wall. DAMN thats thick, pricey and heavy. why not use some .120 wall, and brace it well? i know the .25 wall was partily used because of the bushing rod...

hey guys, i need to redo my wiring for all my accesory's. i need to run power to, tach o meter oil pressure gauge coolant temp gauge UUUGGGAAA horn back up light doom light electric fan wipers (switched) turn signals (switched) whats the best way to go about this. i know they should have...

i have my windshield wipers mounted to a toggle switch where the inside mirror's were. and now when i have them on i get a constant white noise from my cb. i'm not an electrical guy by any means, so please learn me