4wd ranger ext cab wanted for 4bt swap
Well its been years since I have been on this forum and many years sine I have had a ranger.....buttttt I'm looking for one again! A roller with or without body. I am wanting to swap a Cummings 4bt into it. Body needs to rust free. Im locate in south jersey.
i have a 3.0 it has a 4.0 auto explorer computer in it i bought it like that. IM trying to find the right computer right now for it. can my 3.0 be getting to much fuel with this computer? when i let off the clutch in 1st or reverse sometimes it feels like its about to die like its getting...
its been snowing for like a week. well not steady for a week but two or three days ago we got over 36 inches and then today over 20 and its supposed to snow again monday! south jersey is a white out!
i need a new ecu for my truck. the one i have in there now is for a auto i need one for a manual. i was wondering how do i go about this? its a 1997 5 speed 3.0 4x4. Do i have to get the same year computer or is there like a set of years i can choose from with a 3.0 5 speed.
i bought a 3.0 about a month ago.. its a 4x4 5 speed manual trans my check engine light is one so i ran the codes. Ten codes are showing. I have manual trans so i shouldnt have shift seleniods or a troque convertor correct? maybe the person before me had to put a new computer in and put a auto...
i have a 97 ranger throwing a code for a missfire in cylinder 2 and 4. It is also throwing bank is too lean in 1 and 2. Its also throwing p1143- air assist control range valve.
cant the o2 sensors be going off because of the missfires.
anyone have any ideas on what this could be or how to...
i have a 97 ford ranger extended cab. I have 5 transmission codes.I HAVE A MANUAL TRANS!!!
could the truck have the computer swapped to a auto computer instead of manual..
P0708-trans range sensor circuit high imput
p0743-Torque converter clutch circuit electrical
p0750-Shift solenoid a...
i had to replace my rear axle and my brake ahrd line broke right above the fitting before it goes into the rubber one.. shoudl i replace the whole line or is there a way i can just replace the fitting it broke directly above the fitting that screws into the rubber line..
so i went out to my truck today and it woudlnt start.. so i started checking things.. turned out my fuel pump wasnt turning on. i checked the fuse on the side of the driver side dash and wiggled it and heard it come on then i tryed to start and it did but then turned off. it did this a couple...
i have a 97 ford ranger 7.5 axle with 3.73 the spiders where welded to the carrier and blew up, but the ring and pinion are fine. i have another 7.5 axle but its from a bronco 2 idk if i want to reweld the perches to the width of the ranger.. could i just take the carrier with new spiders and...
i have a 97 3.0 5 speed with a 7.5 blown to hell.. i got another 7.5 out of a 89 or 90 bronco two.. the only problem is on my 7.5 under the truck is that the drums are bigger then the new one.. am i able to just open the pumkin up take out the c clips and just swap backing plates? so that i can...
so todayy im driving the truck and in first to the end of third i hear this tiny ting ting ting ting. it only makes the noise when i give it gas i know its not a knock in the engine or anything but does anyone else know what it could be?
so i let my ranger sit for about a couple months this summer when i blew the engine the brakes worked great before. Now im driving it and my back brakes only work.. i really dont want to replace the front brakes have any idea what this could be?
well i just put a new 2.9l engine in my 88 ranger. i started it up once and it ran nice then once i turned it off and it would not start again.. The truck is turning over but wont start. i checked to see if i was getting gas and i am i checked for spark and i guess im not getting any. so i...
i have a disk brake dana 44 from a early bronco it needs calipors but i do not know the year. my question is will any calipor froma early bronco fit this? or do i need to know the year?
will the stock trac bar off a eb dana 44 work?
im doing a sas and iw as wondering if i could just use the stock track bar off the axle or do you guys recomend making a new one?
i know there 8mmx1.25 but i cant find them anywhere i even called the dealership and they cant get uhm.. does anyone know a site where i could get them or have a extra set?
So im putting in this new engine i was take the old exhaust manifold off they block on the old engine and the snappedddd.. does anyone know what the size is for the bolts so i can go to the hardware store and pick uhm up?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.