trans

Hey guys! I have an issue with the AT shift cable on my Ranger consisting of it being shortened by the truck having a 3” body lift. The plastic tabs holding it in the bracket on the side of the trans have worn down and won’t hold anymore. Temporarily I have a couple hose clamps holding it in...

What is this plug right above the shift linkage for? Could i possibly use it for my trans temp gauge? Thank you 90’ Ranger A4LD

I Have a 95 ranger 4.0 4x4 5 speed with an electronic transfer case. Im looking at a trans from an explorer that is a manual, from a 4.0 but has a manual transfer case. Can I use my electronic transfer case on the donor trans? Looks like it should work.

97 Ranger XLT, 4.0 engine, M5oD trans. Did complete drivetrain overhaul a month ago, all went fairly well except now fifth gear won't stay engaged. Had trans all apart, replaced bearings & syncs; reassembly went well, all shifting seemed fine. Get it all back in the truck and first road test i...

I just picked up a 83 ranger with a 2.2L diesel and 4 speed manual, my question is does any other ranger trans bolt up to this motor? Like a 2.3 or 2.9 trans? Thanks

I have a 92 Ranger 3.0 V-6 2 wheel drive with a A4LD, shifts fine but it does not go into overdrive. It only shifts 2 times and I can't feel the converter lock up if it has a lock up. It was like this when I bought don't know how long it's been like this. It has no over drive button on the...

to start im new to using forumns in general so i apologise if i do it wrong i just got a 1995 for ranger xlt extended cab 2.3 engine manual trans the slave cylinder is leaking we went to change it and found the crossmember rotted i cant seem to find a exact match i found this...

so I found this other thread and they just stopped without really throwing the answer in my face....heres the link http://www.therangerstation.com/forums/showthread.php?t=79775 I am having all of the same symptoms... heres a quick rundown if u don't wanna click the link... put 3x...

I have a fm145 in my 87 broncoII, and it was making a lot of noise in all gears other than 4th. So I figured bearings and pulled the trans. Have not broken the trans down much yet but can def notice the slop in the input shaft. Found bearing, seal, gasket, and synchro kits and am planning on...

I have a 1996 ford ranger with a 2.3L 4cyl with a manual transmission I plan on doing a 302 engine swap. I want to sell the engine and trans an was woundering what its worth. It was 200K miles on it but runs awesome! Routine mantian has always been done and also just had a recent tune up.

Here's the breakdown Went and played in the snow with my bronco II i negelected to watch my trans fluid temp and stopped at it had hit 290F So i stopped and checked no nasty brown fluid but it smells burnt. So my question is a hot flush and band adjustment nessasary now? Things to consider, the...

Well my 1988 ranger 2.9 needs a tranny. right now it has the mitsubishi d50 in it. looking for a upgrade to something a lil better. would like to here i can get a remanufactured one by chance. please send any info to gi728@yahoo.com. thanks Joe

i have a 1993 ranger with a 4.0 and a A4LD trans. I want to put 4x4 into my ranger since its 2wd now. i have a doner ranger its a 84 with a 2.9 L and 5 spd trans it has a bw-1350 and a d-28. is it possible for me to bolt this t-case to my 2wd transdo i need a different trans to make it possible...

my felxplate sheared in the middle, i got the trans off and the plate off the t.c. but i cant get the bolts that held the flexplate to the crank, any i deas of what to do to get them off?