• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

how to test a coil


Boggin

Well-Known Member
Joined
Nov 3, 2007
Messages
5,711
Reaction score
48
Points
48
Transmission
Manual
what is the most accurate way to test a coil? i think i may have mine blown on the mazda. thanks
 


adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
Grab the prop rod or some other part of the body. Then stick your tongue on the end of the coil wire and have someone crank the engine over. If you survive, you need a new coil. If you survive and have brain damage or need a pace maker now, you probably still need a new coil. If you die, you don't need a new coil, you won't be driving anymore.



Seriously though, if it's a distributor system, I like to take the dizzy end of the coil wire and jam a Philips head in it and hold the driver about 1/2 inch from the prop rod. Then have someone crank the engine. If you hear a sharp snap and see blue spark it's good. If you hear a weak crackling and see orange or red spark, coil time.

If you are not in direct contact with the body you shouldn't get zapped.

If it's a coil-pack system do the same thing, but pull the fuel pump relay first. And you gotta do it once for every coil.
 

4.0B2

Well-Known Member
Supporting Member
TRS Banner 2012-2015
Joined
Sep 24, 2009
Messages
10,700
Reaction score
151
Points
63
Location
Walls, MS
Vehicle Year
1988
Make / Model
Ford
Engine Size
4.0 v6
Transmission
Automatic
can you get a hold of one off another mazda? me having the ex and b2 with an ex's drivetrain, i just swap parts around
 

Boggin

Well-Known Member
Joined
Nov 3, 2007
Messages
5,711
Reaction score
48
Points
48
Transmission
Manual
Grab the prop rod or some other part of the body. Then stick your tongue on the end of the coil wire and have someone crank the engine over. If you survive, you need a new coil. If you survive and have brain damage or need a pace maker now, you probably still need a new coil. If you die, you don't need a new coil, you won't be driving anymore.



Seriously though, if it's a distributor system, I like to take the dizzy end of the coil wire and jam a Philips head in it and hold the driver about 1/2 inch from the prop rod. Then have someone crank the engine. If you hear a sharp snap and see blue spark it's good. If you hear a weak crackling and see orange or red spark, coil time.

If you are not in direct contact with the body you shouldn't get zapped.

If it's a coil-pack system do the same thing, but pull the fuel pump relay first. And you gotta do it once for every coil.
:icon_rofl::icon_rofl::icon_rofl:

i knew of that way but just wondered if there was a better way, like even some way to do it with a test light or volt meter?
thanks though!
 

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
You can always ohm the primary windings, but that test is ineffective at best since a new coil and a functional but weak coil will usually ohm the same or close, and I've done resistance tests that showed good on non-functional coils.

Using a test light or voltmeter to test it is not a great method for a few reasons. "Slow" firing of the coil is still thousands of times a second. That makes it hard to accurately gauge how well it fires since it is running at thousands of hertz while your eyes can process about 60hz. Also, these coils produce up to 40 Kv and a few hundred amps. that will just fry your meter and probably your test light too.

A load test with the screwdriver or an actual spark tester (which functions much the same way) is the best and most accurate method.
 

lil_Blue_Ford

Well-Known Member
TRS Forum Moderator
Supporting Member
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
8,208
Reaction score
5,962
Points
113
Location
Butler, PA, USSA
Vehicle Year
95
Make / Model
Ford
Engine Size
4.9L
Transmission
Manual
So that's how the spark plug tester screwdriver I picked up is supposed to work...

Wasn't sure how it was supposed to be used, I got it without any instructions, just a flat head screwdriver with a spring in the handle and it's labeled "Craftsman Spark Plug Tester." I threw it in my toolbox and it's sat there for the past 4 years or so...
 

AgPete139

09/2014 OTOTM Winner
Supporting Member
OTOTM Winner
Solid Axle Swap
TRS Banner 2010-2011
TRS Banner 2012-2015
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 12, 2007
Messages
2,863
Reaction score
61
Points
48
Location
Houston, TX
Vehicle Year
1997
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0L OHV
Transmission
Manual
2WD / 4WD
Solid Axle Swap 4x4
Total Lift
~9"
Tire Size
35"x12.50"x17"
Boggin, when did you get the Gen3?
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top