• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Dodge b block


jsutton2723

New Member
Joined
Nov 14, 2014
Messages
1
Reaction score
0
Points
0
Vehicle Year
92
Make / Model
Ford
Transmission
Manual
I have a 66 361 dodge motor I was wanting to slide into my 92 ranger it's already got a 727 behind I and I have a 9in ford rear end I can bolt in anybody done a dodge engine swap have any input?
 


RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,363
Reaction score
8,369
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual

Mac

Well-Known Member
Supporting Member
V8 Engine Swap
Joined
Aug 9, 2007
Messages
5,103
Reaction score
183
Points
63
Age
77
Location
C. Wisconsin
Vehicle Year
2003
2000
199
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
That link posted by Ron shows the Mopar to be 2" longer, 3.5" longer but the killer looks like 200 lbs heavier. Never seen that series of motors swapped.
Dave
 

bobbywalter

TRS Technical Staff
TRS Event Staff
V8 Engine Swap
TRS Technical Advisor
TRS Banner 2012-2015
TRS 20th Anniversary
Ugly Truck of Month
TRS Event Participant
Joined
Aug 9, 2007
Messages
23,470
Reaction score
4,668
Points
113
Location
woodhaven mi
Vehicle Year
1988
Make / Model
FORD mostly
Engine Type
V8
Engine Size
BIGGER
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
sawzall?
Tire Size
33-44
My credo
it is easier to fix and understand than "her"
i have worked on la engine setups, and have seen big block chrysler ford and gm installs.


its the same in basics across the board. there were some 413 trucks in ranger and dakota in the lincoln park area at one point as well.
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,313
Reaction score
17,766
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
Dunno nothing about them but you need this intake :D:



They look friggin cool :icon_thumby:
 

bobbywalter

TRS Technical Staff
TRS Event Staff
V8 Engine Swap
TRS Technical Advisor
TRS Banner 2012-2015
TRS 20th Anniversary
Ugly Truck of Month
TRS Event Participant
Joined
Aug 9, 2007
Messages
23,470
Reaction score
4,668
Points
113
Location
woodhaven mi
Vehicle Year
1988
Make / Model
FORD mostly
Engine Type
V8
Engine Size
BIGGER
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
sawzall?
Tire Size
33-44
My credo
it is easier to fix and understand than "her"
it needs that blow by tube after 10000 miles too. :D
 

AllanD

TRS Technical Staff
TRS Technical Advisor
Joined
Jun 1, 2001
Messages
7,897
Reaction score
134
Points
63
Age
62
Location
East-Central Pennsylvania
Vehicle Year
1987... sorta
Make / Model
Ford
Engine Size
'93 4.0
Transmission
Manual
the Chrysler "B" engine is the shortest stroke and thus the revviest character of any of the common big block engines

The part that needs to be understood is that the short deck "B" engine
(as opposed to the 413, 426wedge and 440 RB (raised deck or long stroke B engine))
has the same stroke as the small block LA engines (273/318/340 engines)

The RARE 383 long ram crossram manifold above plays t the revvy nature of the Chrysler B engine, the best part of doing this swap is that once you have a 361 in and running you can replace it with a 383 or 400.

But I will note that your 361 is an engine that will not be happy with unleaded gas as it was designed for the lead additive of 1960's gasoline to protect the valve seats.

the only B engines produced in the unleaded gas era were the B-400 and the RB-440, but I would not recommend swapping on later heads unless they are left bolted to the larger engine they came from...

I used to have a dodge 300 maxiwagon van with a built 400 and a 727 trans t would pass everything but an Amoco station and drag anything like it wasn't there

Particularly after I removed the Edelbrock Victor single plane manifold and holley 850 DP carb the misguided previous owner
put on it in favor of a stock dual plane manifold and
a Rejetted Carter AVS I robbed off my spare 340 Dart engine (Betcha you didn't know I was a Dodge guy long ago...:)
 
Last edited:

Sponsored Ad


Sponsored Ad

Staff online

Members online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top