• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

brake upgrades for 2011 Sport 4x4


jz78817

New Member
Joined
Mar 23, 2016
Messages
7
Reaction score
0
Points
1
Location
Detroit, MI
Vehicle Year
2011
Make / Model
Ford
Transmission
Automatic
Hi-

I have a 2011 Ranger Sport 4x4, and the brakes suck. not only have I had to replace the pads already at 45,000 miles, but a few days ago someone made a left turn in front of me and even practically standing on the pedal it was in no hurry to stop. I know the next time it needs pads I'll probably have to replace all four rotors, so I'm wondering if there is a pad/rotor combo I could use which might improve stopping power. I realize the Sport has bigger wheels and tires than other Rangers, but in a panic stop situation I'd expect at least the rear wheels to start to lock up and trigger ABS.

Thanks,
Jim
 


JoshT

Well-Known Member
Supporting Member
V8 Engine Swap
TRS Banner 2012-2015
Joined
Aug 6, 2007
Messages
3,870
Reaction score
1,727
Points
113
Location
Macon/Fort Valley, GA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Transmission
Automatic
2WD / 4WD
4WD
Your truck already has the best brake set-up that ever came from the factory on a Ranger. You've got another issue because that truck should be stopping good as is.

What type of pads did you install?

Sounds like you did not replace the rotors when you replaced the pads. Did you at least have the rotors turned (machined)? If not I doubt that the new pads bedded properly to the rotors.

Have the brakes ever been bled on the truck? It's possible that some air has managed to get into the system. Might be time for some fresh fluid and bleeding the system.

Probably best "upgrade" you could do are good quality pads and rotors when the time comes to replace them. Think something like Hawk or EBC for pads, and a good quality set of plain rotors. Drilled and slotted rotors won't improve your braking unless you keep glazing the pads, and they will wear out your pads faster. Also bleed the brakes.
 

pjtoledo

Well-Known Member
Supporting Member
U.S. Military - Veteran
Joined
Oct 5, 2007
Messages
5,382
Reaction score
2,963
Points
113
Location
Toledo Ohio
Vehicle Year
20002005199
Make / Model
Fords
Engine Size
3.0 2.3
try pulling the front rotors and sand the glaze off them. lightly sand the pads, then do a break-in procedure.
pull both front wheels off, leave the rotors on, have an assistant rotate the other wheel so you get an even pattern. putting a sanding disk on a drill or whatever gives a nice swirl pattern.
check the slider pins too.

if the front disks are getting thin, trash 'em.
 

gw33gp

Well-Known Member
U.S. Military - Veteran
TRS Banner 2010-2011
Ham Radio Operator
Joined
Aug 7, 2007
Messages
1,733
Reaction score
536
Points
113
Location
Costa Mesa, CA
Vehicle Year
2002
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0 SOHC
Transmission
Manual
2WD / 4WD
4WD
Tire Size
33"
I had braking problems occasionally when my Ranger was new. All I had to do was upgrade the pads to a better performing pad. I started with Raybestos Super Stop pads and when they stopped making those I went to Akebono pads. It brakes very well with the upgraded pads and I tow a lot with significant weight.
I always have the rotors turned when I do a brake job. I bought an extra set of rotors so when I get ready to do a brake job I can get the spare rotors turned and ready to install when I pull everything apart.
 

jz78817

New Member
Joined
Mar 23, 2016
Messages
7
Reaction score
0
Points
1
Location
Detroit, MI
Vehicle Year
2011
Make / Model
Ford
Transmission
Automatic
Your truck already has the best brake set-up that ever came from the factory on a Ranger. You've got another issue because that truck should be stopping good as is.
"best" for a Ranger doesn't mean they're not still sub-standard :D especially because I also have to replace the parking brake shoes; one of them fell apart recently.

What type of pads did you install?
generic Wagner stuff. I was in a hurry at the time because I had a wheel off for something else and was caught off guard by the pads being so worn down.

Sounds like you did not replace the rotors when you replaced the pads. Did you at least have the rotors turned (machined)? If not I doubt that the new pads bedded properly to the rotors.
yes they were turned, but will need to be replaced this time.

Have the brakes ever been bled on the truck? It's possible that some air has managed to get into the system. Might be time for some fresh fluid and bleeding the system.
not last time, but this time I definitely plan on bleeding/flushing the system while I'm mucking around down there.

Probably best "upgrade" you could do are good quality pads and rotors when the time comes to replace them. Think something like Hawk or EBC for pads, and a good quality set of plain rotors. Drilled and slotted rotors won't improve your braking unless you keep glazing the pads, and they will wear out your pads faster. Also bleed the brakes.
that's what I was looking for, thanks.
 

Sponsored Ad


Sponsored Ad

Staff online

Members online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top