• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

replacing steering box


1993rangerxl

New Member
Joined
Apr 16, 2013
Messages
129
Reaction score
0
Points
0
Location
Florida
Vehicle Year
1993
Make / Model
Ford
Engine Size
4 banger 2.3L
Transmission
Manual
Started with leaking return line, replaced, ran less than two minutes and blew out seal on top of steering box. Have reman box will start work in the morning. Can use any and all help, suggestions, shortcuts, little things not mentioned in Hayes repair manual. Thanks in advance to all that respond.
 


adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
Make double super sure to lock the steering wheel in the straight ahead position, and center the box before installing it.

To center the box put some vice grips on the input, they don't have to be super tight. Then turn it all the way one way, turn it all the way back counting rotations, then turn it half way back again.
 

cvar

Member
Joined
Apr 27, 2012
Messages
588
Reaction score
19
Points
18
Vehicle Year
1997
Make / Model
Mazda
Engine Size
4.0L V6
Transmission
Automatic

Chris_1

New Member
Joined
Feb 1, 2009
Messages
88
Reaction score
1
Points
0
Vehicle Year
1994
Make / Model
Ford
Transmission
Automatic
Remove the pitman arm first, that will be the hardest part usually. Go out tonight and soak the 2 line fittings on top of the box with penetrating oil so they will have a chance of coming undone tomorrow. The fitting usually freezes to the steel line.
 

1993rangerxl

New Member
Joined
Apr 16, 2013
Messages
129
Reaction score
0
Points
0
Location
Florida
Vehicle Year
1993
Make / Model
Ford
Engine Size
4 banger 2.3L
Transmission
Manual
Lines came off with no problems. Got the nut off pitman arm and have broke the puller! Pitman arm has not budged!
 

FritzTKatt

New Member
U.S. Military - Veteran
Joined
Mar 9, 2012
Messages
707
Reaction score
4
Points
0
Location
Ohio
Vehicle Year
04
Make / Model
Ford
Engine Size
3.0
Transmission
Automatic
Did you set the pitman arm under pressure, then whack it more/less gently with a hammer? Soak it in PB? I was stressing my puller, then used some percussive maintenance and it came right off.

Never went back on though... refuses to fully seat (nut goes on all the way, but not as much as it did), broke a 1/2" breaker bar putting the nut on LOL.
 

forgey4x4

Member
Joined
Feb 16, 2014
Messages
87
Reaction score
0
Points
6
Location
Washington
Vehicle Year
1989
Make / Model
Ford
Engine Size
2.9l both
Transmission
Manual
My steering box already came centered so see if it says it on one of the papers, I replaced the power steering pump at same time, still trying to bleed the air out of it, still pretty whiny. Not driving it right know so not big deal i go out there and watch a show and turn it back and fourth. Fun other than bleeding its not bad
 

rfl

New Member
Joined
Mar 17, 2011
Messages
118
Reaction score
0
Points
0
Location
Utah
Vehicle Year
93
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
It you have a large vise, I would take the box out with the pitman still attached to it (you still need to take it off the center link) and then put the box in the vise to get the pitman arm off.

Remove the wheel liner to make getting to the hoses, and bleeding the system, much easier.

If the truck has seen off-road action in the last 21 years, you will likely find a bunch of dirt inside the frame rail where the bolts go through to the box on the driver side. Spend a few minutes to clean it out.

Flushing can take 30-45 minutes and a big mess if you do it without help, or 5 minutes and no mess if you have someone to either hold the return hose over a container, or rock the steering wheel so you can hold the bucket.
 

1993rangerxl

New Member
Joined
Apr 16, 2013
Messages
129
Reaction score
0
Points
0
Location
Florida
Vehicle Year
1993
Make / Model
Ford
Engine Size
4 banger 2.3L
Transmission
Manual
Ended up taking it to a repair shop. They said it was a real b.... even after applying heat. Done now. Still have small leak now, trying to find source.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top