My 88 Ranger 2.9L oil pressure sensor is leaking. I bought a socket that fits it. The motor mount is keeping the socket from going on all the way. I even took the black plastic cover off the sensor. Any help is much appreciated
I got the Alternator out the output connector looks good not burnt or falling apart. I spun the pulley on the alternator it makes a lot grinding noise. Its the original one never been changed. I will order one from Napa I should not have to change the connector. I may have to use this fan and...
I know mine has the crappy plastic slip in connector. I should take it off look it over first maybe its bad. What is the best way to get that apart? I know it slips in with two slide over snaps and locks in. The wire don't have much room to lift it up to get to it and it looks like a pain in the...
My Ranger looks like the Alternator went bad. My battery light on the dash flickers its has 11.63 volts when running. My turn signals began to blink slowly. The battery light use to come on than off all the time but had no starting charging issues. My Napa store has a remanufactured Alternator...
Thank You Ron
Your info got me on the track on timing I got the 10 degree mark right with the timing pointer. I have two timing lights both close. I will bring my timing light with me just in case. Its hard to see looking between the radiator hose and battery with the timing light
Thank you
I got it loose with a short ratchet I got a question on timing? The smog place marked the TDC mark on the pulley in white. He told me to disconnect the spout connector set the timing light at 10 and move the dist bring the TDC mark down to the timing marker. This would be 10 degrees...
Thank you both so much
What is the best way to loosen the distributor hold down? its back in a tight spot hard to get to. What size mm socket do I need
My truck failed CA Smog
The inspection on pre smog test the timing is at 5 degrees BTDC they want factory spec at 10 degrees BTDC. The tech marked the pulley told me to set it there set the timing light at 10. I got an old Sunpro advanced timing analyzer. It has degrees advanced on back will...
Need quick help
My 1988 Ranger 2.9l I started it up to warm it up it was running fine on its own for 20 minuts than it just died or stalled. I went to start it back up it just turns over wont start back up. I checked the fuel pressure at the rail tuned the key on pushed the nipple deal fuel...
I been trying to figure this issue out my 2.9l is a pain in the Azzz to start when cold. I have to put the throttle to the floor the starter spins until it starts real slow RPM's than picks up. Once it starts its rough like a miss once warmed up runs smoother. I get on the road 35-65mph its like...
TRS guy's
I got a new issue with my 2.9l it was running fine no issue for a long time. This last week it started this rough idle all the time and it now surges at all speeds and has a lack of power. I pulled all the plugs no fouling all burning good. Its kinda strange it will be bogging lack of...
I been having this issue the last few weeks when the engine cools sitting overnight its real hard to start. I try to let it start on its own than I have to put my foot to the floor. It turns over many times than finaly I get it fire. It sounds like its loaded up trying to clear its self out...
I got this strange issue my driveway is up hill on cold start up I get a blue cloud of smoke. Its just a few seconds than clears up once warmed up nothing even if sitting a few hours on the driveway. If I park level on cold start up nothing clean no blue smoke. I checked the PVC and cleaned it...
I got a quick question?
I got an 1988 Ford Ranger coolant reservoir tank with window washer reservoir tank together. I got if off a wrecked Ranger in my friends old yard with only 35K on it before it was hit. My question is where is it vented at? it has the stock push in black plastic plug cap...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.