Recent content by emo666

Very little improvement with gas cap off--going to new oxygen sensor and check exhaust-ran some seafoam thru also- no go!!

fuel pressure good--but have a partial fuel symptom maybe?..been having for years tho didn't seem to bother the truck. I can't fill the gas tank more than 5 gallons at regular nozzle speed than I have to drizzle fuel into gas tank or it will back out an splash out of the fill pipe. Had a garage...

ok--my 1989 ranger 2.9 not accelerating . It starts fine runs fine at low speeds---but push done and it bogs and goes nowhere. It has no engine light or codes. Changed out ignition module on distributor,changed coil, new MAP senser. Map senser fixed it for a week or so but now its back to...

I have a fuel injecter problem #5 not working -would like to replace all 6 but want to know which one to buy. On Rock auto they range from 35 to 50 apiece. --Can someone tell me what is the difference for the price. I don't want to have to tear it down again in a year. Only manufacturer...

When I change my oil on my newly rebuilt 2.9 1989 bronco II --My oil filter is not filled completely--it will drain over the sides when losing it --but when I get down to the drain pan it seems not completely full. I noticed it on the first change but forgot about it. All of my dash gauges...

Does anybody know if they make a 2 piece rear engine seal for a 1989 bronco II. I rebuilt my engine last year and it has developed a rear seal leak. Would prefer not to pull the tranny or engine. Dropping the pan on a 4 wheel is not easy either ????? Also my ampmeter and oil gauge are...

Looked all over google and can't find the vinyl jacket that holds the female end of the seat belt up so it can be easily attached on my 1989 bronco II. I need 2 tan colored ones--mine are broke and collapsed beyond repair.

Been checking thru here for days and can't find a good source for the TINY plastic or ? lines that feed the controls for the air conditioning and heating for a 1989 Bronco II. The parts stores have nothing that small in rubber to repair the breaks. Where do I find something I can use. P.S. I...

OK--went into tech library --printed out work sheet for TFI. everything looked good --BUT-- the spout reading from the harness--cranking is high at 10.6 volts --go to the coil and it does flicker. Did not go into the computer to pin 56 as I'm totally lost when I opened the kick panel. Is...

I'M REALLY--REALLY LOSING PATIENCE with my Bronco.. OUICK HISTORY---rebuilt engine-put a set of "supposedly good heads on---BAD coolant Leak--passed all the tests, compression, 150 lbs pressure thru spark hole, etc. Thought it was a manifold gasket leak-changed gasket 2nd time. Still bad...

Just rebuilt my bronco 2.9 and after tear down 2 times chasing a coolant leak --first time caught it reasonably soon before the oil became too mixed with coolant --this time was worse as it is pretty foamy. How or what should I do to flush this contaminated oil before it wipes the brand new cam...

Finished rebuilding my 1989 bronco II but have a severe undetectable coolant leak. Thinking it's a lower intake gasket. So doing over--BUT -- need the" know how" on getting it sealed. P.S---did compression test--good very little water from tail pipe no visual leaks or...

Just rebuilt 2.9 bronco engine and reused an used set of rubber valve cover gaskets . the heads are 1986 and the block is 1986 but the rest is 1989. Can I use the turned up style vavle cover (1989) on the older heads and get a good seal. In the technical section it states that the older heads...

Where's the best place to buy a reconditioned ICM for a 1986 4 cyl 5 sp ranger? I see a lot of suppliers out there on the net but want a good quality one. I've got a rough idle problem that lasts a minute or so then straightens out but happens every time you shut down and restart. I.ve...

Where can I purchase a EXCELLENT" quality ICM for 1986 4 cylinder 5 speed ranger. There's a hundred rebuilders on the net --who's the best??