Search results

Okay so I found a 1990 Ford bronco with a 302 and a zf5 transmission. I'm putting it in my 1985 Ford ranger 5 speed 4 wheel drive. Should it be an easy swap or will I have any problems?

I'm getting ready to put a 302 in my 1985 Ford ranger. It is 4x4 and manual transmission. I was wondering does anyone know what type of transmission I need to get. I was told the original one won't be able to handle the torque in the 302.

I'm looking into putting a 302 motor in my 1985 Ford ranger 4x4 standard and it has a lift on it. What is the best compatible transmission to go with the 302 motor? Also I've heard that headers will not enough clearance for them.

Where can I get a distributor for a 1985 ford ranger v6 2.8 duraspark

I'm going to replace the distributer and the pickup coil. Does anyone know how to mark it so I don't throw the timing off?

Ok so I'm trying to replace the pickup coil in my 85 ranger v6 2.8 duraspark. I'm trying to pull that round paddle looking thing out with 2 pry bars but it won't come out n I'm afraid I will break it. I really need help

My 85 ranger wasn't getting any spark. I put new coil, plug wires distributer cap n rotor and it started right up, ran for 10 mins then died and won't start. I'm thinking the pickup coil inside the distributer. Any other ideas would be appreciated. I hope this works. I will put it in today.

Hi everyone, so I got the lower rear thermostat housing taking care of, no leaks. The truck was sitting for about 3 weeks, ran fine when I parked it. Went to start it, battery was dead. Bought a new battery and it cranks really slow and no spark from any of the spark plugs. Replaced the coul...

Does anyone know of any other year or vehicle that has a rear thermostat housing like my 1985 ford ranger has. I can't find one anywhere. Not at a junkyard or online. I really need one thank you

Hey everybody my 1985 ranger v6 2.8 litre is making really loud annoying lifter sounds. What's the best additive to help quiet them ty

U all are going to love this. I bought this 85 ranger v6 2.8 litre 4 wheel drive 6 months ago, found in a barn for 1000$ good find, minimal rust some bondue on rear wheel wells, solid suspension n lifted. So far I have had to put a starter in it, a new carb a regulator and that's it. So I...

I am so stoked. I swapped the old carb with the 2100 adjusted the idle mixture screws by ear and it's running better than it ever was with the old one, very happy with this carb for now. Can't wait to put a 352 in it someday. I meant 351 lol

I am so stoked. I swapped the old carb with the 2100 adjusted the idle mixture screws by ear and it's running better than it ever was with the old one, very happy with this carb for now. Can't wait to put a 352 in it someday.

Ok guys, so I bought a 2100 carb swapped it out and it started right up. Now, how do I get it to idle and run smooth?

The choke isn't working and it's leaking gas. Instead of rebuilding the carb can I swap it out with a 2100 is it compatible.

I have a 1985 ranger v6 2.8 litre 4x4. I want to put a new carb on it. What's difference between the 2100 and the 2150 except for emissions? Which one is better. I'm thinking the 2100 for power.

I have a 1985 Ford ranger v6 2.8 litre w a 2 barrel carb. Can I put a 4 barrel on it with an adapter plate.

I just bought a 85 ranger. It sat in a barn for years and has minimal rust. It runs good except I think I need to check the lifters because they are noisy. I put seafoam in the gas and it quieted them some but I can still hear them when I'm driving and accelerate. My question is the 2 barel...