Search results

Unusual question I suppose since i couldn't find anything through search but, Is there a wider brake pad for the rear of the 8.8? So that it covers more of the rotor? i have an unsightly ring of rust on the rotor because the pad is only an inch or so wide. might just be me but its annoying lol

Basically I want to do air bags in the front on my 91. I want to keep a stock height. Has anyone done this? And how difficult? Do you have any pictures? No real reason other than my coils are getting bad. And it seems like it might be fun. Thanks, Travis

does anybody know where i can get late model non-Ranger wiring diagrams? or maybe someone has an account with a website? I need the entire vehicle diagrams for a 2005 Ford Freestyle 3.0L FWD. Also i need the wiring diagram for a Viper 5101 remote start/ Keyless entry. The one that came with is...

i havent posted much lately or even in the last year. But i have been working on a little project. I have been doing a motor swap in my 91. i was given a free motor and trans about a year ago, so i decided i would go ahead and get rid of my 2.3L. The motor i was given was a small block Chevrolet...

Just thought that this should be put in the tech section. For the 2.3L engines Some certain year Rangers ( I believe 93+) come with stock tubular headers. This is a cheap little upgrade from a junk yard. Mine cost 20 bucks. Only thing is the EGR is a PITA to put back together, this if you...

any body have any pics on how your sway bar on your 8.8 is setup? I wanna see how and where you mounted it to your frame and just general pics of it

I have seen it done before i just was wondering if anyone had pics and maybe a little tutorial on how they did. thanx tlane3546

Somewhere i read of someone putting an 88 escort cam in their stock ranger head? anyone have a clue about this? higher lift maybe?

i would just like to add a little to the hi/lo beam mod. Just recently i did this mod and noticed that my wiring is a little different then what is stated in the tech article. Not much different but it can throw you off and to save anyone the hassle of melting wires and blowing fuses i figure i...

im not sure if this is where to post this at...but some how my frame is bent up in the rear and its making my rear end sit funny( one side is higher then the other). When i measure it its only about and inch but it make a significant impact on the appearence. Is there a way the pull it down and...

Has anyone tried this mod where you take the relay and wire it up so the low beams stay on with the high beams? How did it work and have you had any problems like melting wires or melting lamp housing?>

So i just installed a new water temp and oil pressure gauge. My queston is what is the water temp supposed to be at for normal temp and what is the oil Psi supposed to be at? Mt oil is reading 50 psi at idle the jump the 72 when i get on it. i know that i should have good pressure because i...

Has anyone put a rack and pinion steering on Ranger the came with a steering gear box? Have any pics? IM thinkng that this would eliminate all kinds of problems tlane

So i went out today to get friction modifier for my 8.8 3L73 and when i asked for it they took me to a product called TRANS-X: POSI-TRAC Limited slip gear oil additive. did i get the right stuff? It has a Ford P/N on it: P/N M2C118-A

Anybody have them on their truck? Any pics too? and how do they perform?

do the ubolts from a 7.5 fit on a 8.8? or are the axle tubes different diameters?

yea thats what i figured, i went out today and got an explorer 8.8 out of a 94 with l/s for a hundred bucks today. :headbang:

http://www.therangerstation.com/tech_library/Axles.html Go to where it tells the axle code for Aerostars and at the bottom of the chart there is a note about Aerostars. It says that some aerostars with the number one in front of the axle code came with spicer/dana 30 axles and aluminum housing.

ok so im in the tech library reading about what axles come with what vehicles. It says that some Aerostar's came with a Spicer/Dana 30 axles with aluminum housing. How hard are these to find? and what are the benefits over a regular 8.8. also what are the specs for the dana 30?

ok so im in the tech library reading about what axles come with what vehicles. It says that some Aerostar's came with a Spicer/Dana 30 axles with aluminum housing. How hard are these to find? and what are the benefits over a regular 8.8. also what are the specs for the dana 30?