Search results

I was offered 2500 at two separate Ford dealers on trade for a $10k-15k F-150 or 250 so I tossed it on craigslist to test my odds. What ya think? http://chicago.craigslist.org/nwc/cto/3045834090.html

It's funny I got this on video because I just pull the phone out in case something cool happened. I did not expect this stuff to be so deep. Had I been paying attention to the camera angle, you would actually be able to see all the water in front of me instead of just what came up on the...

I've been going back a forth on build projects for a 2wd summer car/truck. I know I'm going to want a 302 with +/- 350hp in whatever I build. It's going to end up being an RX-7, Miata, or 4/5 dropped 98+ Ranger. What I'd like to do is pick up a block for cheap, bolt it up to a stand, and...

It runs on 3 AA's. it turns on by movement (anytime the trucks running basically) and turns off when left still in an upright position (1,3,5 gears)

My buddy got new 35s on his big chevy and I noticed his bushwackers look pretty sweet. I'm getting a 6" SJ class II and 33's, but my 31's are like 75% and could definitely use the resell cash towards a lift. My fenders are rotted out pretty bad. What if I were to buy some full size bushwackers...

Didn't see anything in the search, but I would have though these would be pretty popular amongst the offroaders. They're on page 94 of the LMC online catalog. For $160 it doesn't sound too bad for a padded, molded plastic/rubber floor to drop in instead of recarpeting. What do you think?

<-- This truck. I have been planning a skyjacker 6" fr/ 4.5" rr and 3" BL with 4.56 gears and 35's for quite some time now. My total tickets about $2800. I love this truck, but I want something more out of it. I'm always the underdog at the gravel pit when it comes to the trails and mud. Plus...

<--- This truck. It's stock right now minus 31's. Going for 6" full suspension lift kit, 3 inch body lift, and V8. I've got buddies who work at the boneyard. My plan for the engine is just to trailer home a parts truck with the complete engine trans, computer, etc. Likely will be an injected...

I've got a 94. Want to put a 3" kit on. Can't find any part numbers for rear bumper brackets. The 95-97 has them. It was my understanding that there shouldn't be a difference with a 94 and a 95. They're clearly the same bumper. So what gives?

When I shut the truck off and open the door. Gas cap seems to be a pretty easy, cheap first guess, but I haven't seen anything from searching to cause this. It's only when there's pressure in the system obviously. My filler neck was alright last time I looked at it when I was bolting my roll bar...

The bumpers look the same from the back, but I know the front bumper mounts are different. I just want to make sure the rear mounts didn't change. There's a black rear bumper off a 2010 on craigs for $100 and want to replace my rusted out one I got from the junkyard a couple years ago.

Seems every time I go out in the trails with my buddies, the wet stuff splashes up in my engine bay real good. Sometimes even good enough to get somethin ignition related wet causing misfiring (dries out everytime no prob). My engine bay is covered with a layer of nasty dried up dirty crap. I...

The fuel door on my B4000 is the only body rust on the truck and I know if I sand it all off and repaint it that I'll never get the paint to look good. I figure since it's all white with a lot of black accenting I'd go with a black Ranger fuel door off a junkyard truck or somethin. I'm gonna...

I drive a 94 reg cab short bed 4.0 5 speed 4x4 B4000 on 31's. I was planning on getting stock height replacements just for the sake of getting back that half inch or so of old spring sag, but I'm considering getting a real light duty plow setup soon. I know I will need some stiffer springs...

I just replaced my clutch this weekend. My exhaust wouldn't unbolt so I cut it clean in between the o2's and the manifolds. Unplugged my o2's and pulled the system free. The sensor on the drivers side wasn't tightened down when I pulled it out. I cut the bolts out that held the flanges, drilled...

In my 94, I'm doin a full clutch job with slave cylinder, rear U-joints (4wd truck), oil pan gasket, and rear main seal. And well, I guess I'll see what comes up along the way. Obviously I'm gonna need engine out for the pan which is okay I have a hoist. I've got all my parts ready, plus I'll...

Where can I buy one for my 94? It seems like the only ones I can find are for 95 & up. I must be looking in the wrong places.

Well my AC has never worked since I got it, but now it squeaks and squeals like no other to the point that I'm embarrassed to drive. If I buy the w/o AC belt and run it, will my engine light be on all the time? 94 4.0L.

My 4x4 94 b4000 5 speed on 31's get like 15-16 combined right now. I've been reading about these Jet Chips improving power, mileage, etc., but how much is true about these? Could I see a solid improvement in my truck? Stock 3.73 diff if you're wondering.

They're on a single relay and switch. Were fine when I put them on, but recently these (and my subwoofer) have been making my volt gauge drop fairly significantly. It's really only obvious at idle. I bought the truck a year ago and have to clue how old the battery is, but it seems like maybe my...