Yeah, it's part 8 on the numbered diagram....
Thanks, I'll check that out...it may be that tube is the issue and not the charcoal canister as you said.
Thanks Woog! Sorry for dealy to reply...Is that pic. at the top of the filler (up by the filler cap?) Or, as you say it is the tube that goes into the actual gas tank? Looks like it's where it connects way down by the tank. I will certainly go with good quality parts for this as you suggest...
Sorry for delay to reply: Yes pump handle clicks off (no gas splash.) I have monitored with ignition on and acts the same. In past I have (ignorantly) filled all the way to the tip top trying to get as much gas in as I could, not knowing this puts gas into the charcoal canister and clogs it...
My fuel fill ups have been gradually getting more and more annoying as the gas pump shuts off (pressure build up) after only a slight amount. After searching around a bit more and describing the situation to a mechanic I was informed that the charcoal canister is likely the culprit. I'm...
I know it's a fairly old thread, but been having same issues with '99 Mazda B2500 for a while. Catalytic converter had a crack and I replaced the cat along with both oxygen sensors and exhaust manifold. The same stall out upon deceleration manifested (no change as it was doing that before and...
Oh, great, I'd appreciate that! I got the wrong part (IAC) from a well known auto-parts dealer and am going through the pain in the (you know what) return process of the IAC. Any live data would help since that's probably my next step is to have a live scan if possible. Please direct private...
Ok, that's interesting...it could be that cleaning the throttle body set things as it should have been all along, but 900? I also noticed (after warm up and driving) it will go to noticeably high idle (like 1,200--1,500 approx)
and stay there for about 15 secs then go back to 900 (which it has...
UPDATE March 14, 2021: As mentioned, the throttle body and IAC was cleaned and the next day I had the idle running high (900 rpm.) The high rpms were an additional new development. To answer what RonD asked,
a cold start up has an initial run up to 1,500rpm and DOES gradually going down to 900...
I'll have to wait until fully cooled down to verify (as I've been running it lately-in Florida:cool:) to verify that. I will try that later (without tapping the gas pedal) and see.
I wish I would have read this before delving into the throttle body cleaning, but it needed to be cleaned for sure. AIC apparently was replaced at some prior time [going by the appearance, evidence of being removed in past and no Motorcraft etching.] I gave it a cleaning along with throttle...
The stalling or wanting to stall issue is intermittent. It only happens when coming to a stop (while winding down to idle.) It will mostly almost stall, but picks back up at the last second before stalling and if I have a load (like A/C or while turning) it will stall. It always restarts...
Ranger Station is a great forum!
I watched over the shoulder of a friend (mechanic) who helped me change my timing belt at the 140K mileage when I first got my 1999 B2500. The belt was loose and was due to be replaced and actually sounded smoother after replacement. Went ahead and replaced the...
I'm getting set to replace my catalytic converter on the '99 2.5L. It sounds like it either has a hole or it's cracked, and I have slight loss of power, but no check engine light. Looks straight-forward (2 bolts at the exhaust manifold) and a clamp with springs on other end. That whole section...
I'm getting set to replace my catalytic converter on the '99 2.5L. It sounds like it either has a hole or it's cracked, and I have slight loss of power. Looks straight-forward (2 bolts at the exhaust manifold) and a clamp with springs on other end.
The question is: would it be a good idea to...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.