• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

1984 2.8 gauges not working when hot?


BrownRangers

Member
Joined
Aug 20, 2019
Messages
76
Reaction score
49
Points
18
Location
Burbank, CA
Vehicle Year
1984
Make / Model
Ford Ranger
Engine Type
2.8 V6
Engine Size
171cui
Transmission
Manual
2WD / 4WD
2WD
Total Drop
3"
Tire Size
245/40/15
1984 Ford Ranger 2.8 2wd with 4 gauge left dial, has fuel, oil p, water t, and amp.

When cold under 60 degrees(CA cold) gauges work fine. Sometimes will go out as truck gets hot or temps get hot. Also wont work if truck is then parked when engine hot and outside temp is hot. Next time you start(say after running into a store) gauges wont work.
When hot, even just ambient temp, say 80 plus, the gauges do not work even at start up.

Any tips?
 


Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
The only logical reason the temperature would effect power to all the gauges is if there is a connection somewhere that is barely functional and as it heats it flexes or expands enough to lose contact.
 

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
The only thing those gauges all have in common is the power source. I think Dirtman is on the right track with a loose connection.

The 1st gen gauges ran on 5 or 6V, not 12 like the 89+. I'd start by pulling the cluster out and inspecting the printed circuit board, PCB damage is usually pretty obvious, it will either take the form of the copper printings pulling away from the plastic sheet, or a big black burnt spot.

I'd also investigate the power feed wire. The 1st gens used a thicker, black,7 to 8 ohm resistor wire to feed power to the gauges from the ignition switch and drop the 12V VPower down to the required 5 to 6V. You have to pay attention when working with the wiring to the gauges. I've burnt out perfectly good PCBs by not being careful enough and hooking 12V to the gauge set.
 

Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
Any updates?
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top