• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

1999 Ranger 3.0 - Auto Hubs dissengaging


cal74

Member
Joined
Nov 11, 2008
Messages
53
Reaction score
0
Points
6
Location
Zumbrota, Minnesota
Vehicle Year
1987
Make / Model
Ford
Transmission
Manual
Working on a new project truck I had planned to sell, but figured I'd keep it over the winter.

Yesterday was literally the first time I've driven it more than a couple hundred yards and today was the first time I've used the 4x4 (other than checking it earlier to make sure it worked).

Shifts into 4x4 and mostly coming to a stop or even slowing down the 4x4 is disengaging. Auto hubs don't sound like they're slipping. Guessing a vacuum leak, but would it be anything else?

Thanks for any tips.
 


RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,291
Reaction score
8,296
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
Yes, vacuum issue

1998-2000 Ranger 4WDs used Pulse Vacuum Hubs(PVH)

Each hub will have a vacuum hose to a Splitter on front axle, then a single vacuum hose from there up to the Vacuum modulator(PVH Solenoid), usually on passenger side engine bay lower down.
Modulator is what the 4X4 module uses to control vacuum going to the hubs, so it will have two Vacuum hoses, vacuum IN and vacuum Out to hubs
And it will have 2 wires

Vacuum IN comes from the vacuum reservoir, black plastic ball, also low down on passenger side of engine bay.

You can trace hoses back to Vacuum Modulator then pull off that hose and "suck on it", lol, or use a vacuum pump, it should hold a vacuum(low pressure) forever, if it doesn't then hoses or hub is leaking.

Vacuum at the Modulator needs to be tested with a vacuum gauge, $20 and every DIYer mechanic should have to test engines, still the best diagnostic tool for gasoline engine since the 1890's, lol.

If your vents in the cab are stuck on Defrost then your vacuum reservoir is most likely bad, cracked or not getting vacuum from the intake manifold, and that would effect the PVH from staying locked.


All Rangers 4WDs have an OPEN front axle, so if one hub is unlocked then NO 4WD, so both hubs need to stay locked to get 4WD.

Manual Hub conversion was popular and sometimes less expensive than servicing PVH system

PVH troubleshooting here: https://therangerstation.com/tech_library/ford_ranger_pvh_hub_operation_and_troubleshooting.shtml

Conversion to manual here: https://therangerstation.com/tech_library/AVM_hub_swap.shtml

You also have an option to just lock the hubs full time, seen here: https://therangerstation.com/Magazine/Apr04/offroad.htm
 
Last edited:

Craig0320

Well-Known Member
Supporting Member
Article Contributor
V8 Engine Swap
TRS 20th Anniversary
Joined
Sep 21, 2017
Messages
1,209
Reaction score
225
Points
63
Location
Mississppi
Vehicle Year
1998
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
My credo
Break it right the first time. Fix it better the next time.
If you are planning on keeping the pvh hubs then I would replace every vacuum line on it. If not, then just slap some manual locking hubs on it as stated above. You could also convert it to a live axle setup.
 

Lanciadave

New Member
Joined
Jun 27, 2017
Messages
11
Reaction score
0
Points
1
Vehicle Year
1998
Make / Model
Ford
Transmission
Manual
Yes, vacuum issue

1998-2000 Ranger 4WDs used Pulse Vacuum Hubs(PVH)

Each hub will have a vacuum hose to a Splitter on front axle, then a single vacuum hose from there up to the Vacuum modulator(PVH Solenoid), usually on passenger side engine bay lower down.
Modulator is what the 4X4 module uses to control vacuum going to the hubs, so it will have two Vacuum hoses, vacuum IN and vacuum Out to hubs
And it will have 2 wires

Vacuum IN comes from the vacuum reservoir, black plastic ball, also low down on passenger side of engine bay.

You can trace hoses back to Vacuum Modulator then pull off that hose and "suck on it", lol, or use a vacuum pump, it should hold a vacuum(low pressure) forever, if it doesn't then hoses or hub is leaking.

Vacuum at the Modulator needs to be tested with a vacuum gauge, $20 and every DIYer mechanic should have to test engines, still the best diagnostic tool for gasoline engine since the 1890's, lol.

If your vents in the cab are stuck on Defrost then your vacuum reservoir is most likely bad, cracked or not getting vacuum from the intake manifold, and that would effect the PVH from staying locked.


All Rangers 4WDs have an OPEN front axle, so if one hub is unlocked then NO 4WD, so both hubs need to stay locked to get 4WD.

Manual Hub conversion was popular and sometimes less expensive than servicing PVH system

PVH troubleshooting here: https://therangerstation.com/tech_library/ford_ranger_pvh_hub_operation_and_troubleshooting.shtml

Conversion to manual here: https://therangerstation.com/tech_library/AVM_hub_swap.shtml

You also have an option to just lock the hubs full time, seen here: https://therangerstation.com/Magazine/Apr04/offroad.htm
Thanks Ron D, that is exactly what I was looking for.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top