• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

B3000 won't start


Guanfy

Active Member
Joined
Jun 22, 2019
Messages
221
Reaction score
91
Points
28
Location
Crawfordville, Florida
Vehicle Year
1994
Make / Model
Mazda B3000
Engine Type
3.0 V6
Transmission
Manual
2WD / 4WD
2WD
Total Lift
Stock
Total Drop
Stock
Tire Size
15in
Recently acquired a new to me 1994 B3000 with 168k on it. Previous owner blew a head gasket and had it torn down to the heads when I made the purchase. 3 months later... I've rebuilt the engine from the block up and replaced the warped and cracked heads along with the bad head gaskets. The truck will now turn over, fire, but not start. I never pulled the distributor during this process nor messed with the timing chain. As far as I can tell the fuel pump is working and spark is happening. Compression seems good as well. Any suggestions on where to go from here?
 


RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,292
Reaction score
8,296
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
Do 50/50 test

Spray fuel into the intake and try to start engine
1. If it starts OK but then dies, spark/timing is OK but injectors are not opening or no fuel at the injectors, or bad fuel :)

2. If it doesn't start up or backfires then spark timing is not right or weak spark
50/50, instant results on what to check

Since you've never heard engine run you don't know what previous owner has done before you got it, so don't "assume' gasoline in the tank is good or that spark timing is right


You can crank the engine a few times then pull out 1 spark plug, it should be WET with fuel, if injectors are working and there is fuel pressure, smell it, is it gasoline :), light it, it should burn easily if its gas
 
Last edited:

Guanfy

Active Member
Joined
Jun 22, 2019
Messages
221
Reaction score
91
Points
28
Location
Crawfordville, Florida
Vehicle Year
1994
Make / Model
Mazda B3000
Engine Type
3.0 V6
Transmission
Manual
2WD / 4WD
2WD
Total Lift
Stock
Total Drop
Stock
Tire Size
15in
That's a place to start. By intake you mean the big inlet on the plenum right?
 

Guanfy

Active Member
Joined
Jun 22, 2019
Messages
221
Reaction score
91
Points
28
Location
Crawfordville, Florida
Vehicle Year
1994
Make / Model
Mazda B3000
Engine Type
3.0 V6
Transmission
Manual
2WD / 4WD
2WD
Total Lift
Stock
Total Drop
Stock
Tire Size
15in
So update. Turns out the spark plugs were most likely one post out of position on the distributor. I moved them, seated them and the truck fired right up. Unfortunately right around engine temp the driver's side freeze plug blew out so.... The plug is very rusted and I think was failing before I got the truck. I'll replace that and see what happens. Thank you for your help.
 

RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,292
Reaction score
8,296
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
Good work :)


You can use the rubber expansion plugs in place of freeze plugs(core plugs), much easier to install in tight spots
 

Guanfy

Active Member
Joined
Jun 22, 2019
Messages
221
Reaction score
91
Points
28
Location
Crawfordville, Florida
Vehicle Year
1994
Make / Model
Mazda B3000
Engine Type
3.0 V6
Transmission
Manual
2WD / 4WD
2WD
Total Lift
Stock
Total Drop
Stock
Tire Size
15in
I am going to try and use the brass ones if possible. I'll buy the rubber expanders as a backup. Everything I am reading is saying that they are more temporary in nature and are more prone to popping out.
 

RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,292
Reaction score
8,296
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
Never found that to be the case in my use of those

But for sure go with what you have used before, brass won't rust, but they can also pop out, in my experience, but only happened twice in 40 years so not a deal breakers, lol
I use steel now if engine is out and I am replacing all of them, then paint them, if you change coolant every 2 years then rusting out from the inside is not an issue, if you don't then they may only last 20 years, or 25, like your 1994 core plug did


The rubber plugs are strictly for easier installs in tight spots
 

Guanfy

Active Member
Joined
Jun 22, 2019
Messages
221
Reaction score
91
Points
28
Location
Crawfordville, Florida
Vehicle Year
1994
Make / Model
Mazda B3000
Engine Type
3.0 V6
Transmission
Manual
2WD / 4WD
2WD
Total Lift
Stock
Total Drop
Stock
Tire Size
15in
Ron,

Thanks for the sage advice. I'll probably buy some rubber expanders and some brass tomorrow so that when I try to do the replacement I can go with what I can actually use.
 

Sponsored Ad


Sponsored Ad

Staff online

Members online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top