• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Black fluid in clutch master cylinder


srisitt

Member
Joined
Jun 1, 2019
Messages
58
Reaction score
8
Points
8
Location
Washington
Vehicle Year
1991
Make / Model
Ford Ranger
Transmission
Manual
Well this can’t be good. Opened up the fluid reservoir in the clutch master cylinder and it is jet black and filthy. What would this indicate and is it possible to flush out myself? I’ve read it can be deteriorated rubber from the cap and lines, but this truck is new to me it could be something else. My manuals only cover topping off the fluid, what can I do for this?

29893
 


RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,290
Reaction score
8,290
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
Just indicates its old, it can happen as early as 5 years but usually closer to 10-15 years old

Yes, you can flush it yourself

Check brake fluid as well

Both systems use Dot 3 brake fluid


And just FYI the black rubber piece in your hand is there to prevent air contact to the fluid in the reservoir, brake fluid absorbs moisture from the air, which causes it to deteriorate faster
You can leave it out while flushing, and you can leave the cap off the reservoir, there is no pressure in the reservoir when you pump clutch pedal, if there is then Master is bad, lol.
 

srisitt

Member
Joined
Jun 1, 2019
Messages
58
Reaction score
8
Points
8
Location
Washington
Vehicle Year
1991
Make / Model
Ford Ranger
Transmission
Manual
Just indicates its old, it can happen as early as 5 years but usually closer to 10-15 years old

Yes, you can flush it yourself

Check brake fluid as well

Both systems use Dot 3 brake fluid


And just FYI the black rubber piece in your hand is there to prevent air contact to the fluid in the reservoir, brake fluid absorbs moisture from the air, which causes it to deteriorate faster
You can leave it out while flushing, and you can leave the cap off the reservoir, there is no pressure in the reservoir when you pump clutch pedal, if there is then Master is bad, lol.
Thank you. That is good news. Would flushing the cylinder be as simple as disconnecting the hose and refilling? Surprised I can’t find more info on this in my manual.
 

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
Thank you. That is good news. Would flushing the cylinder be as simple as disconnecting the hose and refilling? Surprised I can’t find more info on this in my manual.

Nope, you need to bleed it through the system as if you were installing a new part and bleeding it, or else you will introduce air to the system.
 

RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,290
Reaction score
8,290
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
Use a turkey baster type device to suck out as much of the black fluid as you can from the reservoir, or unbolt it and dump it out
Refill with clean fluid, to the top
Open bleeder on slave
Some fluid will flow out from gravity
To speed things up you can use a helper to push down on clutch pedal while you open and close bleeder valve

Its good to put a smaller rubber or clear plastic hose on the bleeder so it drains into a container vs squirting out

Open bleeder
Have assistant press down clutch pedal to the floor, hold it down
Close bleeder
Release clutch pedal
Repeat until fluid is flowing clear

Maybe 5 or 6 pedal presses

KEEP RESERVOIR TOPPED UP!!!!!!!!!
Or you will get air into the system
 

4x4junkie

Forum Staff Member
TRS Forum Moderator
TRS 20th Anniversary
Joined
Aug 19, 2001
Messages
10,749
Reaction score
580
Points
113
Location
So. Calif (SFV)
Vehicle Year
1990
Make / Model
Bronco II
Engine Type
2.9 V6
Engine Size
2.9L V6
Transmission
Manual
2WD / 4WD
4WD
Tire Size
35x12.50R15
I dealt with this situation on my BII years ago shortly after I got it.
I recall it took a good bit of fluid before it started to come out decently clean from the slave (I think I used up about a third of one of those big quart-size bottles of DOT3). It was nasty.

×1000 on the reservoir! If air gets in, you'll soon learn just how much fun it is to deal with Ford's dumb air-trapping inverted master cyl design.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top