• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Explorer Axle Conversion - Forked (Dented) Driveshaft


PetroleumJunkie412

Official TRS EV Taunter
Supporting Member
TRS 20th Anniversary
TRS Event Participant
Joined
Oct 31, 2018
Messages
7,826
Reaction score
6,565
Points
113
Location
Dirtman's Basement
Vehicle Year
1988
Make / Model
Ranger
Engine Size
2.9l Trinity
Transmission
Manual
2WD / 4WD
4WD
My credo
Give 'yer balls a tug. Fight me.
He's got a welder. And cost for balancing is only about 50 bucks around here. My place does it on the car, takes about 30 minutes.
Ok. You have my.full attention. Have something I can.read to see what I.have to do?
 


pjtoledo

Well-Known Member
Supporting Member
U.S. Military - Veteran
Joined
Oct 5, 2007
Messages
5,338
Reaction score
2,908
Points
113
Location
Toledo Ohio
Vehicle Year
20002005199
Make / Model
Fords
Engine Size
3.0 2.3
So, in getting ready to put the 8.8 Explorer axle in my ranger, I picked up a one piece driveshaft out of a 1999 extended cab.

The forklift operator at the junkyard I use typically annihilates driveshafts on pickups, and today I THOUGHT I got a hold of one that he didn't mangle.

Until I took it out of the bed of my truck when I got home.

So, the new one piece is dented from forklift forks. It's not "bad" per se, but it definitely has a flat spot in it. Maybe 1/16-1/8" deep dent, 6" long. It's forked up. (trying to make myself laugh here)

I'll post some pics tomorrow morning

So... What are my options?

about the fork lift driver? depends on how devious you are
 

PetroleumJunkie412

Official TRS EV Taunter
Supporting Member
TRS 20th Anniversary
TRS Event Participant
Joined
Oct 31, 2018
Messages
7,826
Reaction score
6,565
Points
113
Location
Dirtman's Basement
Vehicle Year
1988
Make / Model
Ranger
Engine Size
2.9l Trinity
Transmission
Manual
2WD / 4WD
4WD
My credo
Give 'yer balls a tug. Fight me.
about the fork lift driver? depends on how devious you are
Ratted him out to his boss this morning. They agreed to take a return.

Still interested in potentially repairing it. Well see I suppose.
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,868
Reaction score
5,030
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
A lathe would be best to remove the welds holding the ends on. I know some have used v-roller stands and grinders to remove the welds. Welding the tube back on is pretty basic.
If you plan on spirited performance driving, a new or rebuilt shaft is recommended.
 

Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
I make a set of v stands from whatever scrap I have. Cut the yokes off leaving extra room (leaving the weld). Then with the yokes off carefully cut the welds and clean them up, check the ends are straight. Put the new tube on the v stands, very very lightly tack on the yokes and then use good squares to make sure they are dead center. If you've gotta break them off and reposition them a few times do it. Make sure they are clocked right as well. finish the weld, check again.

I built the shaft in my mustang and have driven that over 110mph with no vibrations. I also did the one on my old ram charger and never even bothered to balance that beast. It's really not a complicated job at all, just need to prep and check, and check and check then check again before finishing the weld.
 

PetroleumJunkie412

Official TRS EV Taunter
Supporting Member
TRS 20th Anniversary
TRS Event Participant
Joined
Oct 31, 2018
Messages
7,826
Reaction score
6,565
Points
113
Location
Dirtman's Basement
Vehicle Year
1988
Make / Model
Ranger
Engine Size
2.9l Trinity
Transmission
Manual
2WD / 4WD
4WD
My credo
Give 'yer balls a tug. Fight me.
I make a set of v stands from whatever scrap I have. Cut the yokes off leaving extra room (leaving the weld). Then with the yokes off carefully cut the welds and clean them up, check the ends are straight. Put the new tube on the v stands, very very lightly tack on the yokes and then use good squares to make sure they are dead center. If you've gotta break them off and reposition them a few times do it. Make sure they are clocked right as well. finish the weld, check again.

I built the shaft in my mustang and have driven that over 110mph with no vibrations. I also did the one on my old ram charger and never even bothered to balance that beast. It's really not a complicated job at all, just need to prep and check, and check and check then check again before finishing the weld.
So what you're telling me is that I can get a measurement off this one, then use the 1995 two piece with the same ends and slip yoke and go to town with chromolly tubing?
 

Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
Well if you wanna use 4130 it's a tad more complex. You should use ER80S-2(6) wire and 98/2 ar/co2 instead of 75/25. You also need to pre-heat before welding 4130 to steel or it can crack. No post heat necessary but should be cooled slow, preferably in cat litter.

Maybe practice on a crappy shaft first...

Regular mild steel tubing is easy, just don't use flux core.
 
Last edited:

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
He's got a welder. And cost for balancing is only about 50 bucks around here. My place does it on the car, takes about 30 minutes.
I can beat that. I know how to balance a drive shaft just using two hose clamps.
 

PetroleumJunkie412

Official TRS EV Taunter
Supporting Member
TRS 20th Anniversary
TRS Event Participant
Joined
Oct 31, 2018
Messages
7,826
Reaction score
6,565
Points
113
Location
Dirtman's Basement
Vehicle Year
1988
Make / Model
Ranger
Engine Size
2.9l Trinity
Transmission
Manual
2WD / 4WD
4WD
My credo
Give 'yer balls a tug. Fight me.

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
All ears.
Draw four quadrants one your drive shaft, making lines in line with the bolts is easiest.

Put a single hose clamp on with the screw in any one of the quadrants. Test drive for vibration. Move the screw around the zones you marked off until you find the spot with the least vibration. If you can't find a spot with no vibration add a second hose clamp and repeat the process until all vibrations are gone. You shouldn't ever need more than two clamps.
 

Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.

scotts90ranger

Well-Known Member
RBV's on Boost
Joined
Feb 28, 2001
Messages
7,925
Reaction score
4,227
Points
113
Location
Dayton Oregon
Vehicle Year
1990, 1997
Make / Model
Ford
Engine Type
2.3 (4 Cylinder)
Engine Size
2.3 Turbo
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6
Tire Size
35"
For the record I had the same experience trying to find a short bed regular cab 4x4 drive shaft when I twisted and bent mine while tractor pulling... couldn't for the life of me find one when I needed it so I took it to a driveline shop and had it redone which cost $450 if memory serves (like I said, bent and twisted, most had to be replaced)... a few months later I found one in a junkyard for $45... now I have a spare :)
 

Shran

Junk Collector
TRS Forum Moderator
Supporting Member
Article Contributor
V8 Engine Swap
Solid Axle Swap
Joined
Mar 4, 2008
Messages
8,637
Reaction score
4,703
Points
113
Location
Rapid City SD
Engine Type
V8
Engine Size
5.0
Having built a bunch of driveshafts at home... my method involves tacking the yokes to the tube, installing the driveshaft into the vehicle, and using a dial indicator while turning the shaft to reduce runout. It's VERY difficult to get it perfect.

My local shop charges around $150 to retube and balance a shaft - totally worth it if you care about vibration. My application is offroad use and I use 1/4 wall pipe - so vibration is expected but I do try and get them as close as possible.
 

Ranger850

Doesn't get Sarcasm . . .
TRS 20th Anniversary
Joined
Jan 24, 2018
Messages
8,426
Reaction score
4,664
Points
113
Location
Tallahassee Florida
Vehicle Year
2001
Make / Model
Ford
Engine Size
Born with a 3.0, looking for a donor V8
Transmission
Manual
2WD / 4WD
2WD
Total Lift
Stock 2"
Tire Size
Stock
My credo
Doing things wrong, until I get it right.
My head hurts from trying to make sense of that. I can even read french and spanish, and none of that helped. Can some one plz tell me what she said.
 

19Walt93

Well-Known Member
Ford Technician
V8 Engine Swap
Joined
Nov 13, 2018
Messages
4,475
Reaction score
4,412
Points
113
Location
Canaan,NH
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
V8
Engine Size
351
Transmission
Automatic
2WD / 4WD
2WD
Total Drop
3"
Tire Size
235/55R16
My credo
If you don't have time to do it right will you have time to do it over?
Balancing a driveshaft with hose clamps isn't "ghetto", the procedure was in Ford's driveline vibration manual they released for the Fairmont.
If you re tube it yourself make sure you have the u joints in phase or you'll never get the vibration out of it. In phase means aligned exactly on the same plane.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top