• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Pinion bearing.


Super ranger 01

New Member
Joined
Mar 7, 2019
Messages
29
Reaction score
3
Points
3
Location
Cumberland Co.Tn
Vehicle Year
2001
Make / Model
Ford ranger
Transmission
Automatic
Hey guys ive got the 8.8 rear end..and i was wondering if there should be any slack or slop in the pinion shaft when the driveshaft is off...i also have the main keeper nut off to replace the pinion seal an noticed that there is some movement in the pinion shaft...thanks
 


Bird76Mojo

Well-Known Member
V8 Engine Swap
Joined
Jun 28, 2009
Messages
2,633
Reaction score
1,264
Points
113
Location
IL
Engine Type
V8
There will be some rotational "slack" - it's set up that way to give the gears the proper clearances as they rotate. It shouldn't be a huge amount though. It's typically called backlash, and it's set within a given tolerance range when installing the differential carrier and the ring/pinion gears. The differential carrier is shimmed from left/right to attain the proper backlash, as well as the pinion shaft being shimmed.

As for up/down or left/right movement, that's not a good sign.

But with the pinion nut removed, of course there will be movement.
 

Super ranger 01

New Member
Joined
Mar 7, 2019
Messages
29
Reaction score
3
Points
3
Location
Cumberland Co.Tn
Vehicle Year
2001
Make / Model
Ford ranger
Transmission
Automatic
So would u most likely say the pinion bearing is shot also?
 

Bird76Mojo

Well-Known Member
V8 Engine Swap
Joined
Jun 28, 2009
Messages
2,633
Reaction score
1,264
Points
113
Location
IL
Engine Type
V8
Hard to tell without actually seeing and feeling it. But if the pinion nut is removed, and that's where the "play" is coming from, then it's not an issue.

If there's a lot of movement up/down or left/right when everything was tightened up (before you tore it down) then yes, I'd imagine the bearing is on it's way out. Unless something wasn't tightened to spec or had came loose somehow.
 

Super ranger 01

New Member
Joined
Mar 7, 2019
Messages
29
Reaction score
3
Points
3
Location
Cumberland Co.Tn
Vehicle Year
2001
Make / Model
Ford ranger
Transmission
Automatic
Ok.thanks..ive got the bearing out an it an the race seems ok but i think since its already out..im just gona replace it...thank u again
 

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,691
Reaction score
13,147
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
That is really not the way you want to do that...

I would put it back together and torque the pinion nut... without the seal installed. Then inspect for movement in the pinion shaft. if OK... remove the nut and yoke... drive in the seal and torque it up.

Replacing just the outer bearing without checking the pinion bearing preload is probably going to cause you issues.
 

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,200
Reaction score
16,337
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.
^^^^ +2

There are 2 bearings on the pinion shaft. You have to remove the carrier to get the pinion out and replace the inner bearing. At that point, you are in the magical realm of "differential setup" it's not the easiest thing to do unless you have the proper tools and experience. Every bearing you replace changes the clearances in the differential. That changes pinion depth, backlash and tooth engagement patterns for the ring and pinion gears. These measurements are set using shims and torque specs. They are measured with a dial indicator, beam style torque wrench and by reading the wear pattern on the gears.
 
Last edited:

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
I agree with all the above.

You can't accurately inspect for axial play on the pinion shaft with the nut off. That releases all the tension and preload that takes all that play out of the system.
 

Super ranger 01

New Member
Joined
Mar 7, 2019
Messages
29
Reaction score
3
Points
3
Location
Cumberland Co.Tn
Vehicle Year
2001
Make / Model
Ford ranger
Transmission
Automatic
I did as u said an checked it wthout the seal in it...all was ok..there was no slack in it when i torqued it...so i replaced the seal an all is back together..thanks guys for all yalls input...im a rookie at the rearend stuff...
 

Bird76Mojo

Well-Known Member
V8 Engine Swap
Joined
Jun 28, 2009
Messages
2,633
Reaction score
1,264
Points
113
Location
IL
Engine Type
V8
I hope you didn't forget to use some RTV on the pinion flange splines when you put it back together. That can be a source for a leak..



GB :)
 

Sponsored Ad


Sponsored Ad

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top