Home Ford Ranger Forum Builders Guide How To Tech Other Articles Featured Rangers Readers Rangers Classifieds Shirts & Decals


Go Back   The Ranger Station Forums > Help Forums - Engine & Transmission Forums > V6 Forums > 3.0 Liter Forum


Thread Tools Display Modes
Old 09-15-2007, 08:35 PM   #1
New Member
Join Date: Sep 2007
Posts: 1
Vehicle Year: 2001
Vehicle Make: ford
Vehicle Model: ranger xlt 3.0
Rep Power: 0
fish62hook is on a distinguished road
Default Change Oil Pan Gasket

I have a 2001 ford ranger 3.0
Ihave been told it is a rough job, I would have to raise the engine by disconecting the motor mount to get it out ,this is a new one on me.

What is the best way of doing this job, any help would be greatly appreciated

fish62hook is offline   Reply With Quote
Advertisement - Don't want to see the forum ads? Click HERE to find out how to be a Supporting Member.

5% Discount Code: 01783FE29A6986 Expires: December 30, 2018
Old 09-15-2007, 08:44 PM   #2
Wicked_Sludge's Avatar
Join Date: Aug 2007
Location: Westport, WA
Posts: 6,937
Vehicle Year: 1993
Vehicle Make: Ford
Vehicle Model: Ranger, Flareside
I use this vehicle for: Attracting the ladies
Rep Power: 38
Wicked_Sludge is a jewel in the roughWicked_Sludge is a jewel in the roughWicked_Sludge is a jewel in the rough
Send a message via MSN to Wicked_Sludge

the best way is to pull the engine out of the truck.

the quickest way is to unbolt the engine and jack it up (if its 4x4 your in for a fun time).

welcome to TRS!
As seen on the internets!

Originally Posted by Hahnsb2 View Post
Dyno sheet or GTFO
Originally Posted by Ranger Dave (B25) View Post
The call was for scantily-clad women. A Certificate of Boob Authenticity was NOT specified.
Originally Posted by Grant Imahara
I'm not sure if we have the right stuff; I'm just hoping we don't have the wrong stuff.
__________________________________________________ ____________________________________
Last edited by Wicked_Sludge : Today at 09:16 PM.
Wicked_Sludge is offline   Reply With Quote
Old 09-15-2007, 10:05 PM   #3
Join Date: Aug 2007
Posts: 1,166
Rep Power: 25
michowski will become famous soon enough

easiest way would be to just pull the motor. I tried the lifting it up some and try to switch pans but it didnt work well at all. Taking the motor out was far easier and I would recommend that way
michowski is offline   Reply With Quote
Old 09-18-2007, 09:49 AM   #4
cargs's Avatar
Join Date: Aug 2007
Posts: 189
Vehicle Year: 1993
Vehicle Make: FORD
Vehicle Model: RANGER
I use this vehicle for: Daily Driver
Rep Power: 23
cargs is on a distinguished road

I changed the oil pan gasket when i had the transmission out. you can drop the pan enough to get the old gasket off and new one on, but you can't get the pan out. make sure to get a one piece silicone gasket, mine was from felpro i believe, it will make it much easier to get lined up if you choose not to pull the engine.
93 Ranger, 3.0L, 5spd, manual t-case swap, MSD ignition, 31x10.5 BFG AT's, 2006 ranger bucket seats, rancho RS500 shocks, Warn 37780 "Jeep" hubs, 2007 Glasstite Raven Canopy.
cargs is offline   Reply With Quote
Old 09-25-2007, 12:23 AM   #5
New Member
Join Date: Aug 2007
Location: hudson. WI
Posts: 10
Vehicle Year: 1999
Vehicle Make: Ford
Vehicle Model: Ranger XLT super-cab 2-door
Rep Power: 0
therangerofdanger is on a distinguished road

don't listen to them. disconnect the engine from the mounts and thread th bolts onto the studs and let the engine rest. it's ok belive me i did this on my 99. you are going to have to drop the right side of the front diff too (one bolt oh well). i think ihad to take out the starter but i have turned 21 sense then. also there are a few things about the new gasket it's gonna look wierd with the tabs (u will know what i am talking about). there are two bolts that are longer than the others. these go on either side of the timing cover. installing it is a bitch because the gasket won't seat right on the pan. remember the old full size? there was a lower and upper half of the splash shield to the bellhousing. i had to cut it off just below the sealing surface on the bottom of the block. it bolts back up in place and i used RTV to seal the gap. it's not as tough as you think. just time consuming. it took 3 days in the shop at my auto tech class but know this i had a teacher that was worried about us i am a tech now a could to it alot faster with out his help just message me with any questions.
therangerofdanger is offline   Reply With Quote
Old 06-16-2008, 05:02 PM   #6
Junior Member
Join Date: Jan 2008
Location: Hugo, MN
Posts: 71
Vehicle Year: 1999 1998 197
Vehicle Make: Ford Ford Jee
Vehicle Model: Ranger Explorer CJ5
Rep Power: 22
kroed11581 is on a distinguished road
Send a message via Yahoo to kroed11581

I know this is an old thread, but I recently did my 99 4x4. I unbolted the engine and transmission at the crossmember, raised the engine as far as i could in the engine bay, removed starter, unbolted front axle and let it hang down on the lower control arms, removed the CV axle on the passenger side, then unbolted the oil pan. When you drop the pan, the pickup tube will prevent you from removing the pan completely from the automatic transmission. I took an air cutoff wheel and cut the inspection plate so i could remove the bottom half of the inspection plate without unbolting the entire plate. I was able to remove the oil pan at that point. Clean the oil pan with brake cleaner and a Scotch-Brite(R) pad, new gasket, some gasket maker and I also used the tabs to line up the holes. Re-assemble is the reverse.

Of course, i ruined my two front ball joints and noticed the CV joints were bad so I replaced those and my experience was not nearly as smooth as I just made it out to be, but if I did it again, I think I could do it as smoothly as noted above. I also found out 2 of my 3 bolts that go into the driver's side engine block were snapped off. When looking at it, the threaded part on the engine block that comes out to meet the mount had snapped off. I managed to get new grade 10 bolts in there with locktite and was able to thread about 1/4" of the new bolts into what was left of the threaded area still left in the engine. Perhaps the previous owner was in an accident? Either way, the truck shifts much smoother now!
Kawasaki GA

Last edited by kroed11581; 01-26-2011 at 05:39 AM.
kroed11581 is offline   Reply With Quote
Old 05-16-2012, 08:00 PM   #7
New Member
Join Date: May 2012
Posts: 1
Vehicle Year: 2001
Vehicle Make: Ford
Vehicle Model: Ranger
I use this vehicle for: Daily driver and fun!
Rep Power: 0
Barney is on a distinguished road

I just did my oil pan gasket due to it being torn when I did my timing chain. I didnt pull the engine, but I did unbolt it from the motor mounts and raise it as far as I could, unbolted the tranny mount, and unbolt the passenger side axel, and it came out.
Barney is offline   Reply With Quote
Old 12-14-2013, 07:35 AM   #8
New Member
adfav1's Avatar
Join Date: Jan 2011
Posts: 21
Vehicle Year: 1999
Vehicle Make: ford
Vehicle Model: ranger
Rep Power: 0
adfav1 is on a distinguished road
Default 3.0 oil pan change

99 3.0 4x4 replacing pan due to rot.i ended up pulling front diff right out,not a bad job just time consuming due to first time.left side unbolt outer tie rod end,upper ball joint and small metal shield on back of spindle bearing 2 8mm bolts. then you can slide out left axle,same on right side except axle will slide out after dropping diff only three bolts for diff.dropp diff then right axle,unbolt starter and remove,having starter rebuilt just because it is out and there is almost 200,000 on truck now.remove two nuts for motor mount and small inspection plate right side of trans two 8mm bolts.remove all bolts from pan then jack front of motor all i used was a 2x2 block of wood and floor jack on the crank pulley,lifted motor about 2 inches and there is enough clearance to drop pan right off.since this was my first time replacing this pan it was time consuming but having all the steps now it will go back together more quickly as soon as i get the parts.
adfav1 is offline   Reply With Quote


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 12:28 PM.

© 1999-2018 / 959 Media LLC / All Rights Reserved