Recent content by bigpotato555

ok I went wheeling yesterday "on 31" enter a small mud hole and got stuck did a few reverse-drive no big deal...and then snap! fawk...broke a front axle didn't pound it or anything....so this morning I went and bought one frome a 2005.."this is for my 07" at first the new one seem longer but...

Ok I install my 4" superlift on my 07 level 2 with 33 tsl...and drove it about 1000 kms.... Went for an alignement...and I need 4 ball joint...which are 500$ for lifetime waranty here... I wonder if it's "normal" the truck as 57 000 kms...or I am going to change them at every 1000 kms or so...

I recently install my lift on my 07 level 2 The only thing i didn't realy notice how the t bar where crank... Now I would like to crank it about an inch... so i crank it so it level and the lower control arm are slightly angle to achive that the driver side bolt was almost tighten to end...

I have build an back rack for my 89 few years ago....and now i ditch the box and going offroad bed... I am now looking to install it on the 07... Does any of you have a pictures of factory bracket for the back rack? I just drill tru the box on the 89 but don't want to do this on the new truck...

I just got a sweet deal on BOTH!!! I just bought both from a 08 reck at my local scrap yard..... Now I am wondering which one to install...I don't really want to install both... I just want to run 33" this is on my 07 level 2 which is my daily driver so... 3" body lift would be good but I will...

Went you put a 3" body lift on level 2...are you able to still use the front tow hook? You the spacing between the rear bumper and towing hitch look bad? thx

Anyone has a torch red level 2 with a flat black grille found on base model? The fx4 half tone have flat black grille and it look awesome.

I bought this level 2 a fews month ago with 25 000 miles on it...and after a week or so I was not happy how it was shifting....it was like the clutch was not releasing enough... So I have it check at my local Ford...and they said that the through out bearing was noisy and that there was like a...

I just bought an 07 level 2...and so far i am not really impress by the locker...I would to have explanation how does the torsen work...since i didn't not found a lot...What i have found so far it that there is a ratio 2:1 or 3:1 which would mean the ratio difference between the two wheels...so...

I am looking to buy an 2006 fx4 ranger....wondering if i could fit 36x10 military on the stock wheel on with only 3" body lift....I don't plan wheeling it...so no travel need just need to be able to steer lol...I would like to have pic of your with tire size and body lift thx guy

I just remove my gas tank to replace the strap and leaf spring hanger and gas tank cross member because they where rusted....and what i found between the tank and the frame was awful... now i am looking for the right way to replate the frame I am thinking of cuting a 36" x 10" x 3/8" flat bar...

Ok here is my situation: I swap my FM146 behind my 2.9l for an M50D behind from a 4.0l. In the process I did a 4.0l clutch conversion...I have put a 4.0l flywheel, centerforce 2 clutch and pressure plate...the guy did 1000km on it...the slave is also new and the hydraulic line from the master...

hey guys have some question here...I bought an 89 grand marquis to put the 5.0l efi into my ranger...but I found out that it's a dam freaking nice car to drive..lol...I have found some gt40 head from a mustang...the guy has the heads, the upper and lower intake and the cam...I am wondering if...

got some question here....i am thinking to swap in a d44 i would like hp...not sure of full width or not..it does look good on the picture doesn't look to wide...anyway i was looking on the shortening 44 in tech library and they say that if you cut 6" out of passenger side EB axle will fit..is...

that a sweet looking truck...i was wondering if it would look to width...got some more??