Search results

Soooo. Winter wheelin up here requires a lot of different driving styles from crawling tryin not to break through and on the occasion doing some drift busting with pedal to the metal. there are often times when I run at or very near the Rev limiter. Typically i never start off running rpm's that...

We were the only rig out of the 5 that wasnt a jeep (Zj, Lj, Cj, Mj and then us in the broncoll)

Need to come up with a rear driveshaft for the explore since i have brought it into contact with rocks a few too many times. rear shaft was extended after the SAS so getting a factory shaft is sorta outta the question current unit is 49 +/- 1/4'' Can anyone give me a rough measurement of the...

these springs came off a postal vehicle that had a rusted out shackle and when the new shackles came in for it they also came with new springs and the works. so these arent squated out at all. might see a little less height out of more used one's. it will clear 37's as you see it in those pics...

might have a hard time fitting 63's under the front. as for ride or flex i have no experience with waggy's just the exp springs. scored a 691 on a 30deg ramp do i think it's pretty respectable rear's were still on the ground

ive been debating on going highsteer or just over the knuckle steering. looks like the highsteer isnt in the cards for me right now as there is still alot that needs to be done before summer rolls around.

waggy's seem to be the spring of choice. however we used explorer rear leafs in the front and rear of a broncoll and have had pretty good results. it will flex, doesnt sway all over the road (like mine) and doesnt require a kidney belt to drive either. think ride quality in that rig are about as...

i have ALLWAYS carried a highlift jack with me in my truck's. Now with upgrading (er. sidegrading) to the explorer from my mazda reg cab short box. i am attempting to keep it in the similare weight range. i have allready minimized alot of stuff in the truck and now it comes to the highlift. I...

so lookin for others thoughts on radial v.s. bias pro's and con's is it worth 300$ more (per set) for radials?

after some hands on further reasearch. the spindle grease tool wouldnt work that wall unless you made it to clear the axle shaft. However i think before i reassemble the front end on the explorer i am going to attempt to modify hub parts similar to the jeep stuff. the only issue is that the...

So in my journey of allways trying to further waterproof my rig I came across this nifty tool for yota's. I dont see why somthing couldnt be easily fabricated to grease the spindle bearings on our axles (35/44/10 bolt whatever). Also could make somthing that threaded on in the same fashion to...

i'm running f-150 springs and it ride's o.k. i also was running a d30 for a couple years, i never had a severe failure but it would eat wheel bearings like no other. it wasnt just mine going through the wheel bearings as 2 other members are still battling with them. i upgraded to a 77 F-150...

i climbed the axle tree. and dont have any regretts doing so.i have learned ALOT along the way. started building the mazda in december of 09 and had 2 d-30's under it before i swaped in the FW 44. i have yet to break anything on it yet. i feel that i run it pretty hard but 99% of the wheeling...

wondering if anyone knows, has seen or has links to a 3rd gen ranger body on a bronco ll frame. the only thing i have found are several gen 1 ranger bodys on broncoll frames and 1 never completed 97 ranger on a bronco ll frame. there is a parts truck (88 bronco ll) in my yard now that is...

well here the start of the build. now 4.0 non-egr, m5od,1354M 77 HP44, 5.13 gears,open, Warn lockuts,, E.B. superflex springs, skyjacker shocks, poly front bumpstops, 1 ton steering,Ruff stuff frame side trac bar bracket, single "heckathorn" steering stabilizer rusty's "high clerance" long...

for those not wanting to order the premade weld on clevis mount all i did was found a couple of old matching recievers (i call em stingers) and took the chopsaw to em. and cut the ball mount area off. i then notched out my bumper counter sunk them in and layed a couple good beads around them...

i plan on pickin up a ford explore in a couple days. the one i'm looking at is a 94 4.0,a4ld,1354e I plan on swaping the the trans and t-case from my mazda into the explorer and vise-versa my pickup has m5od and 1354m just verifying that when swapin the computers they are the same size as they...

hard to tell from the pics but had less than an inch of rain all summer. with the conditions it would have been more fun wheelin on 31's than 37's most of the holes were barely up to the rim all summer. the holes that are typically truck swallowers were at least managable. most of them would...

well everyone says how weak dana 30's are. mind you i wheeled mine HARD on 33's and then allwinter on 37's (without failure). but aparently they cant hold up to direct impacts with rocks at high speeds. I hope all these pics work here's a try. imediatly after the axle broke it vered HARD to...

Was asked by one of my long time wheelin buddies to help him build a new truck. so i got all the details of what he wanted. curved them in a slightly different direction as a trail truck shouldnt need a step ladder to get into. and off we went building. Plans are Factory 4.3 700r4 10 bolt...