Search results

help!! im stumped...when its cold out..anything below 50 degrees, it will turn over but wont start. after about 6 tries, it will sputter, after 10 tries, it will start and run on what seems to be a cylinder or two for a few seconds...after several of these tries,5 or more minutes and it...

im having a problem with my b2, when its cold the engine barely runs...sounds like its running on 1 cylinder. after it chugs away for a minute or two it will straighten out and run great...only when its cold does this show up...i replaced the ECT sensor and still no change. the temp gauge is...

anyone know if these arms will fit my b2? look like a good deal.... http://www.summitracing.com/parts/slf-03-1130/overview/

will adjustable camber/caster bushings from my dana 28 fit my new dana 35??? need to know asap so i can order them if need be....thanks!

i got a 92 ranger to swap axles with...dana 35 front with 410 gears...just right for me right now even though the rear is a 7.5. the front is easy,just swap them. the rear(which i thought was going to be the easy one)it turns out, is a little narrower. i could live with this for now till i get...

does anybody have any plans drawn up for these?? i want to have some parts cut out so i can weld them up and wondered if anybody had some plans i could use??

http://www.fourwheeler.com/news/1406-is-the-ford-bronco-ii-making-a-comeback/

the body on my b2 seems to be an inch over to the left....could my body mounts have let the body shift over?? want to fix this and was going to do a 1 inch body lift, so i was wondering if anyone had seen this before??

picked up a set of bushwacker pocket flares for 40 bucks! need to fix one but what a deal...anyone know if i can use fiberglass on them?? they look like some sort of plastic..any ideas?

the ratio ends in a 4.....any ideas?

Does anyone know the pitman arm nut size...I'm at the store now and need a wrench

anyone try these??? http://www.summitracing.com/parts/axt-axk8746/overview/year/1986/make/ford/model/bronco-ii

still having trouble with play in the steering and wandering....looks like i have some movement at the steering box where the pitman arm bolts on....any ideas??? is my steering box shot??

hey guys, im thinking about trying something...with my 6 inch ttb lift in the front, the base for my coils is a little slanted forward. my coils are kinda curved because of this. im going to try to take a wedge for leaf springs that is made to correct pinion angles and putting it under my coil...

yesterday did not go well...the special fork i bought did not remove the camber bushings and i resorted to cutting one of the lips off of the bushing and now im drilling it out! slow going as i dont want to damage anything...what a day! anybody have any ideas for when i get to the other side???

hey all, finally getting a few things done on my b2 and thought i would keep a log of this project. my b2 is an 86 eb, been sitting for a few years, paid 400 for it and towed it home. when i got it home i put in a new computer relay and it fired right up!

i picked this up at the wrecking yard today but i thought my ends would attach to it? it is a first gen explorer shaft...is this correct?

hi, does an 86 bronco II have the axle on top of the spring from the factory??

hi all, figured i would say hi...former owner of a 68 bronco and lots of other fords, including a 99 4x4 ranger that i should have kept,my harley bagger and my 67 mustang..just bought a 86 bronco II that needs a lot of tlc...will be around a little more now for sure. nice forum and lots of great...

hi guys, i finally found a bronco II and towed it home a few days ago. its an 86 eddie bauer. its been sitting a while and and the driveshaft was in the back when i got it. got it running and went to bolt in the driveshaft and it was too short?? being unfamiliar with that type of shaft, i...