Search results

This is a question for all you Duraspark gurus. Like the title says can I use an ignition module from a v8 for a v6? I currently have my truck durrasparked with the blue box and the box I am looking at is also a blue ignition module. Any thoughts?

I just cracked the headers I had on my truck. I got them used many years ago. I can not for the life of me find anyone who still sells long tube headers for the 2.8 4wd trucks. Anyone know if the 2wd headers will fit? Or know of a source for the aerostar headers/manifolds? Did they ever make...

Hey I'm reading up about replacing the timming cover and the book says use an aligent tool for the reinstall. How easy is the cover to align without the aligntment tool? Is it worth the $49.00 from eBay?

Any one put a cam in their little motor? I have to rebuild the top end of the motor and am going to put a cam in it, Im just not sure which one. If you have camed your motor I'd like you thoughts on it, along with the specs of the cam, your motor, and truck. Comp cam says they have 3 cams...

Here is the back ground. I have an 84 ranger with an external slave cylinder, which I replaced 5 or so years ago. I had not driven the truck for nearly a year but before I stopped driving it the clutch master began to leak. When I got into the truck last weekend the master cylinder was dry...

As the title says. I am moving to maryland just out side of DC, with my 84 ford ranger, on full width axles, 38" swampers. What are the laws like for tires sticking 6" past the fenders? It currently has 3.5 inches of lift over stock but stands decently high cause of the tires. What are the...

I might have a set of ford 2.8L heads up for grabs. If I can get them sold so i can buy a motor from a local guy, I will got this route instead of rebuilding my motor. The heads are fresh from the machine shop where they have been compression tested and had the exhaust valves and guides replaced.

No i don't want to hear from anyone why would you do that, or your just polishing a turd! I just want to hear what people used and what your thoughts of the cam you used. Im thinking of the stage 2 cam mentioned in the tech page and wanted to know if anyone has used that one in a truck before...

Are these heads susceptible to cracking?

hey what do people use when reinstalling their t-cases? Can not find the gasket that goes between the two. should I make my own gasket again:( or rtv it up?

I have an offy dual plane intake and it needs a new gasket between the upper and lower halves. Anyone know of any auto parts stores that carries these gaskets? I made the last one but it was a bitch and would like to not have to make another one. Any help would be nice. Thanks

Anyone who has a slightly to well worked 2.8 still use the stock fuel pump? I feel like my fuel pump is not keeping up with my motor. The fuel level in my clear fuel filter changes radically based on how I drive. Lots of idle almost empty. Hard and fast almost empty, slow and steady, nice and...

I have an offenhauser dual plane intake. Which end of the upper intake goes forward(closer to the radiator), the large open end, or the small long runners end? The front of the carb has the primaries and the back( closer to the fire wall) has the vac secondaries. I think I had the upper...

Do any trucks have a drive shaft matching this length with 1310 u-joints?

I need a cv driveshaft in the 47" lenght. Do any of the new rangers use a driveshaft like this?

How much of a pita is it to move the steering box 3" forward? I stretched my wheel base 3" forward for my sas. Now my drag link hits my tie rod when the drive side wheel is stuffed. Entertaining ideas.

Like the title says. What do I torque the rear flange bolt too? If I over tighten the bolt it pulls on the output shaft and the t-case will not shift out of 4wd to 2wd. Am I missing a spacer?

Like the title says. What is the torque of the rear flange bolt on a t-case. Thanks.

For all you people who have made there own doubler plate out of 1/2" steel how do you align the front t-case with the rear t-case? Do you attach the plate to the rear case put the sector shaft in and align the front case on the plate where is feels like it will not bind when the input shaft (on...

I have a ranger project that needs a cv style rear drive shaft. I need it to be approx 47 inches +/- and inch or two. Do any rangers come with something like this stock? If so what years? Thanks