lift

hopefully some of you can tell me what went wrong...i have a 2000 4wd that the springs were flat...so after reading a bunch i thought explorer leafs would be the best option...i went to my local u-pick and found a set off a 98 4 door with 80000 miles looked like they were in great...

So I was reading in the tech library and I was wondering if disconnecting the loom wires and other lines/wires is needed? Can't I just take off the bumpers and take out the radiator and simply put the blocks where the body connects to the frame? Im planning on doing this lift kit over the summer...

:dunno:is there anybody who can or know of anybody that can either make or fab some beam drop brackets for a 6 inch lift, i am goin to put a d35 in from a d28 and the lift plate will be too close to the carrier housing... any ideas are greatly apreciated thanx:icon_welder:

i have a 2006 ranger supercab 4x4, and i was wondering what the biggest size tires i can fit on it without lifting it anymore...there is already a 2 inch lift on it..

I have a 1988 Ranger with a 2.9l and a 6inch skyjacer lift with 33's. I just bought a 1965 ford 289. My question is what all do I need to do the swap besides (engine mounts,headers,oil filter relocator,and an oil pan) What type of tranny should I use? Can I use the stock t-case? Any info will help.

http://cgi.ebay.com/ebaymotors/6-83-97-Ford-Ranger-Rear-SoftRide-Leaf-Springs-_W0QQcmdZViewItemQQhashZitem35acbf9195QQitemZ230531502485QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories#ht_3145wt_1165 from my understanding all leaf springs are the same there for these should work on any year. my...

i have a 2010 Ranger are there any body lift kits available yet i'd like a 3in back and 4in in the front

I've got a 2000 2wd ranger and I wanna lift the rear up a bit without using blocks. I'm piecing together the fabtech 5.5 front so I'm going for around 4 in the back and I would like to use leaf springs from an explorer but I dunno if they'll fit right. I couldnt find a FOR SURE answer so my...

I have an 88 Ford ranger 2.9 L super cab 4x4. The truck has been lifted excessively and is in desperate need of the one piece drive shaft swap. Locally I have not been able to source one. I found one in a salvage yard in Phoenix (about 150 miles away) out of a 2003 ranger, 4x4, extended cab...

So I am looking to lift my ranger extremely modestly (don't want to be modest, but even that's a stretch right now). I am just looking for a little bit more clearance, and larger tires. My budget for this is about $25 a month* after all is said and done with the bills, so this is going to take a...

I've changed things around on this first post to make it in compliance to [TOTM standards] Here is a recap for those who don't know. I picked up a 1993 Ranger 4x4 as a project truck. It had a new(ish) motor put into it not long ago. It has a light bar hoop, 3" body lift and new rims. The body...

Ok so I'm new here but hear me out. I just bought a 1998 ford ranger 4x4 that was previously a one owner car. The previous owner blew a head gasket on the motor causing the antifreeze to ruin the motor. After this the previous owner decided to tear the whole thing down, stripping the old motor...

What is the basic need to know info for lifting a 2wd 2005 Ford Ranger? Also what is the biggest tire i can fit stock? Thanks

Hey guys, So like everyone on here I'm looking to lift my 2wd Ranger. I eventually want to build it into a prerunner but that won't be for a long time so for now I just want something that will lift about 2" and give a stronger ride than stock but not be bouncy. I want to try and avoid the...

Hey everyone. I have a 1987 Ranger STX and i am looking to lift it. The local 4x4 shop told me i couldnt get a lift bigger then 4 inches for it but i wanted to put a 6 on it. If anyone could help me out that would be great! Id like to not have to put it on myself because im really busy with work...

I know this has been done and ive seen it on s10s. my questions r about width and the extent of work to be done. i have a 1996 4cyl 5spd 2wd ranger. i want to run d30 front, rubicon 4:1 transfer case, ford 8.8 LS 4:10 and disc brake rear end, custom driveshafts(JUNGLE DRIVESHAFTS). wat type of...

I'm in the process of trying to decide where to cut and turn the i-beams. I use the truck mostly for driving, and the occasional weekend trip to the local ORV park. I've seen a lot of people cut and turn them at the ball joints, or they cut them in the middle of the beam. What I'm wondering...

I was wondering how many people have done this mod? And how long it took on average? What were any problems anybody ran into? And where is the best place to start?

I already have a 4" suspension lift. I was wondering if there were anything to get another 2or 3" lift out of the suspension to clear 35 or 36? I'm lookin for something cheap. Got any ideas?