Search results

I was wondering if anyone has come across a site that sells replacement arm rests for the door panels of a 1989 Bronco II. Mine are very much worn out and I was hoping to just replace them with a bolt on application as oppose to having to rebuild and foam/upholster new ones. Any help is much...

I was wondering if anyone has come across a site that sells replacement arm rests for the door panels of a 1989 Bronco II. Mine are very much worn out and I was hoping to just replace them with a bolt on application as oppose to having to rebuild and foam/upholster new ones. Any help is much...

I am in the midst of installing the Painless dual batery kit in my 89 Bronco II and have a question. I need to tie the system into a wire on the truck that is HOT in the RUN and START positions. Does anyone know what wire i can tie into and its location??? I'm hoping to save time by asking the...

I am in the midst of installing the Painless dual batery kit in my 89 Bronco II and have a question. I need to tie the system into a wire on the truck that is HOT in the RUN and START positions. Does anyone know what wire i can tie into and its location??? I'm hoping to save time by asking the...

So i chopped the top off my 89 Bronco II and have reached the point of installing a tailgate. Now, I know a ranger tailgate will work but my question is....Am i restricted to the 84-92 ranger tailegate or will a mid 90's one work? The reason I'm asking is that my local wreckers have an...

So it has been many a year that i have wanted to cut the top off the old BII and now that i bought a house with a shop i can finally do it. The plan was to chop the roof only but as i got working on the project i also decided i would strip the interior, relocate the ECM, remove the various...

So i am in the process of removing the cancerous areas on my truck and replacing them with fresh metal. During this process i came across some cancer i was unaware of. It is located at the front of the door jam. My question is as follows.... Does anyone make a replacement panel for this...

I'm looking to relocate my ECM in order to avoid having it hit the drink again. I was just hopin that someone out there has relocated thier ECM and has pics or details of where they relocated it to and what was involved. Any help would be much appreciated. And my BII is an 89' with the ECM...

So aside from LMC truck, where can a person find a new rad support for a decent price. Any help is much appreciated.

I'm looking to do high steer on my full width 79 bronco dana 44 and keep the 5 on 5.5 bolt pattern. What do I need to carry this out? Do I need to find ford flat top knuckles? Is it possible to do it with Chevy flat top knuckles? Let me know whats been done. Thanks

I am looking to get new axles for my 9" since one is bent and the splines on both are twisted. Here is my dilemma. I don't know what axle I need (i.e. big bearing/ small bearing etc.) Here's what I have: 28 spline axles Bearing diameter over 3" (leads me to believe it is a big bearing) Axle...

Has anyone maneged a way to mount an e-brake to the back end of the t-case in a BII? Pics would be great if its out there

I was pondering putting an Atlas II into my BII since my current t-case is on the way out and I may as well put something beefy in. I was just wondering if there were any other aftermarket t-cases out there for the BII or if there are any other options I could explore. Let me know what you...

I have an '89 BII with the high back bucket seats. They are starting to show their age and I was wondering if anyone has come across some comfortable bucket seats (after market or from another car/truck/van whatever) that I could swap in. The current seats are comfortable enough but if I'm...

Anyone have a reason as to why this may be happening?

I recently did a 4.0L swap into my 89 B2. I used the wiring harness from a 91 Ranger since it is the closest to plug and play there is. The truck runs just fine, however I do have a few bugs: 1) I am getting constant power to the cab for some reason. No key in ignition and radio, wipers...

I am in the process of doing a 4.0L swap into my BII. I was just curious as to how people have connected the BII lines to the Explorer stainless steel lines. It has me stumped. Thanks.

I'm doin a 4.0L swap into my bronco II. I just need to know what each of the hook up points on the starter are supposed to be connected to. I know the larger one is for the power wire. What is the smaller nut for and also the male connector. Any help is much appreciated.

I'm attempting to install the power steering pulley on my 4.0L. I was just wondering how far I press the pulley on. Do I go till i can't turn the nut any more or do I leave it out slightly, or do I line it up as best I can with the other pulleys on the engine. Any help is much appreciated.

So I have dropped a 4.0L into my B2. I have started putting the wiring harness in and just have a couple questions: 1) Is the o2 sensor the same on the 2.9L and 4.0L? Can I just plug in the o2 sensor that is already attached to my exhaust or is there a 4.0L specific one? 2) What the hell...