Search results

Been working on this thing for close to a year now. Trying to make it I to a reliable DD and back up kid hauler, but I've run into a snag. I can't find any help figuring out a legal and self doable way of putting 3 point belts in for the rear seats, without being accused of child endangerment...

I am in need if a speedometer cable for a 1990 4x4 bronco ii. Did a 4x4 swap on a 2wd that did not come with the factory dummy case, and my cable doesn't reach the case. This is going to be my daily, and it's almost on the road.

I was wondering if anyone has ever added shoulder belts or 4 poimt harnesses to the rear seat in a Bronco 2. My oldest child is too tall for booster seats with the harness, and I'm looking for a step up in safety from the lap belt. This bronco has to serve as my daily and main kiddo transport...

Yet again I'm kicking myself for getting rid of my parts vehicle before completing my project.... I need pictures of the Bronco II parking brake cable routing and connecting parts from axle cables to front cable. I have the front cable, and new rear cables, but when the axle was swapped into my...

At some point a long time ago, the e brake got pushed with the brake cables disconnected. I've tried pulling the release and pulling the pedal up, but it's stuck. Pedal does not move at all. Release is working as best as I can tell, but I've not wedged my 350 lb self up under the dash yet to...

In desperate need of the fuel lines for a 1990 BII from the frame rail, to the fuel rail. I need to style with quick connects on both ends. Don't have a yard near me with a BII or second gen ranger on the yard. Pulled a the motor from a parts vehicle for a project, and stupidly sold the parts...

Has anyone ever put bucket seats in the rear of a Bronco II? I've seen it done on a 1st Gen explorer on another forum, but I can't recall ever seeing it on a BII. I'm sure it's possible, with some flat bar and welding, I'm just curious to see if anyone has done it yet. I'd like to do it with my...

1989 B2 2wd, auto trans with the dummy tcase. Bought with a bad 2.9, started swapping a replacement in, bolted it up, and it got put on the back burner. Been there too long, it's time to go. $700. 1st generation explorer. Been so.lomg I can't remember whether it's a 91, 2, 3, or 4. Complete...

Looking for an explorer 8.8 with 4.10 gears. Would consider 3.73, but really looking for 4.10's. Prefer drum brakes as the vehicle I'm putting it in has drum brakes now. In or near NC.

It's been probably close to a decade since I've been on here, so let's see if you folks are as helpful as I remember... I'm getting a 2000 Ranger 4x2 with a 3.0 that was wrecked in the right front. I'm trying to find a bumper fit it locally, but I'm having no luck. I have a few questions that...

Even as I type this I can feel glaring and hear scoffing, but here goes anyway: I recently purchased a 2000 windstar to replace my wifes ailing 92 explorer that needs major work and with a second child on the way, more space for a second car seat is needed. I picked it up stupid cheap with an...

Im not sure this goes in this section or not, but doesnt really matter to me. Ive been doin a lot of searching at other forums lately for information on some builds i plan to do on my Ex. There have been some changes in my life since i last posted here at TRS. I have finally decided to take the...

Ok, so now that i finally feel like working on my projects again (the new job has done wonders for me) i have a few questions. FIRST: Where can i find a decent cam to match a .060 over bore, ported heads, and port matched intakes? I realize im still restricted by the throttle body bore, so i...

Well since october 2006 i have been working for a local Ford dealer as a Technician. Recently on a trip to the local junk yard after work to source some sploder parts, the owner offered me a job.....outta the blue! He gave me some time to think it over, and after a week i figured salaried work...

SO me and the GF were recently out doing some picture runs (shes in school for photography/graphic design) and she took this picture of me and my dads replacement ranger. It is an 89 ext cab 2wd truck with a 2.9 and a mazda 5 speed. Its a really nice truck and i love driving it. it kinda looks...

I have a set of 2005 mustang 4.0 SOHC injectors at work that i removed from a customers car for no reason other than they thought they clicked too loud. Id like to know if they are similar enough to 2.9 injectors to be used in my built motor to provide a little more fuleage with having ported...

Can anybody tell me what package this ranger has on it? thanx, fwm.

Well its been day two of my first ever Ford manufacturer training...basic electrical. For those who have been there, you understand, for those who havent......its like yawning and sighing all at once. Im learning things 10 times over i had learned in tech school, but in a better way for some...

I always try to keep track of my fuel mileage, and recently within the last 2 fillups i have dropped from 19.75 to 17.6. I have also not been using an mid grade gas like i was previously, and the temperature has dropped considerably requiring the usage of the defroster in the mornings to clear...

Recently, i have gained access to a set of explorer axles, 3.73 geared with a limited slip in the rear. Ive been wondering for sometime if upping the gear ratio in my current explorer would harm or help my mileage. Currently im running the stock 3.27 (according to tech library) ratios. If i swap...