I have a 1993 Ranger, 4x4, automatic. When the 3.0 lost a couple of cylinders, I replaced it with a 4.0, A4LD out of a 1994, 2wd. I changed the tail shaft in the 2wd transmission to maintain the 4x4 capability but I used the 2wd ECM (F47F 12A650 CPA). From a swap perspective, I have had no...
After several months of driving my ‘93 Ranger with a very poor running 3.0, I finally got off my butt and swapped in the 4.0. It was a bit of a task since the 4.0 came out of a ‘94 2wd and needed to go into a 4x4.
I started with a Delta Cams rocker arm/push rod kit in the 4.0. That was pretty...
I disassembled my 1994 A4LD last night. It came from behind a 4.0. It has about 158,000 miles on it and has never been apart (at least not since Dad bought the truck with less than 20,000 miles on it).
When I removed the center support, there was no thrust washer or bearing between it and the...
I am getting ready to use my '94 4.0. When I was driving it every day, I don't remember any significant valve train noise. However, after sitting for a while, anytime I would start it to move the truck the engine was quite noisy. I know the 4.0 is prone to rocker arm to pushrod wear.
This...
I have a 1993 Ranger, 3.0, A4LD, 4X4. I have never been satisfied with the power (more specifically, torque) output of the 3.0, though, in its defense, it has never been 100% as long as I’ve owned it.
The 3.0 is now dead. It has 0 PSI in the # 3 cylinder. I’m pretty sure this is due to a broken...
I am preparing to swap the 4.0 out of my 94 2wd into my 93 4x4. The 93 currently has a 3.0. Both trucks have A4LD transmissions.
My understanding is that the 4.0 bellhousing can be used on the 3.0, 4x4 transmission.
Are there any internal transmission differences between the 4.0 2wd (truck was...
Helping my brother replace rockers and pushrods in his 91 Explorer, 4.0. We're ready to put it back together and noticed the rocker shaft bolts are torque to yeild. Advanced Auto parts shows "brackets" with bolts for $50 per side. This is unexpected and un budgeted, not to mention the time...
I've been out of town for the past few weeks. The rental company offered me a choice between a Mercury Marquis and a Wrangler Sport. That was a no brainer!
So far I have pretty much behaved myself. Although, hypothetically speaking, if one were to take a 2011 Wrangler on a trail and...
Has anyone used Mile Marker hubs on a D35, TTB, RVB? I can get these really cheap. (It’s good to have family connections) So unless I find out they are junk, I will be installing a set next week.
The consensus of those I have spoken with is they are “Good stuff”.
Also, does anyone know if...
I have a 1993 Ranger, 3.0, Auto, 4x4. I did a lot of digging in the tech library and discovered it has the hybrid front axle. I have several questions about this axle. Since the tech library has been reformatted, I haven’t been able to locate some of the info I had previously found.
My...
I have a 1994 Ranger, 4.0, auto, 2wd. It got rolled.
I bought a 1993 Ranger, 3.0, auto, 4X4. It wont even get out of its own way.
I know the 4.0 wont bolt to the 3.0 belhousing but, can I use the 4.0 belhousing/torque converter on the 4X4 trans? Or am I way off in left field here?
These tires came on my Ranger when I bought it (235/75 R15).
They have good tread and aren't dry at all but my right front tire shakes like crazy between 60 and 65. It's bad enough that I'm sure people driving next to me can see it.
I need to replace it but haven't been able to locate this...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.