Search results

I've done compression tests on my motor and have found #3 cyl. Is somewhat lower than the other three. I'm just wondering what the compression in psi would be for a healthy engine. Maybe the other 3 are low too, but #3 is the worst. Engine has over 300k on the clock and is throwing codes and...

Hi all, Got a '94 Ranger 4 banger & 5sp. When I step on the brakes the rear brakes pulsate BAD. No pulsing brake pedal, just rear brakes pulsating. At first I thought it was the brake drums were out of round so I had the drums turned, and put new shoes, springs, etc. Still the exact same...

Hi all. I've got a 1994 2.3, two wheel drive Ranger and It's been running rough and sucking gas for a couple months now. I checked the codes it showed codes for # 158 "MAF sensor voltage high. and #337 EGR sensor voltage high. I checked wires to both all was well. Replaced MAF sensor, no...

Just looking for some input here. I need to repaint my rims. They're off an old cop car and was wondering if I should go with black or go with red. Any ideas? I'm kinda stuck. See attached picture. TIA

I've been looking for new front floor pans for my '94 xl and can't seem to find any. I can find them for older and newer but not for mine. Any leads? Thanks in advance.

Hi all, I did a scan on my '94 2.3l Ranger and it says "canister purge solinoid". Well my truck doesn't seem to have one, not even on vacuum diagram. Is my scanner just dumb or am I? TIA, Bob

I installed a vacuum gauge in my dash and now I noticed an issue. While crusing at a constant speed 40 - 60 mph or more vacuum remains at about 12 BUT goes up to 18 for a second then back to 12. This happens about every 3 or 4 seconds. RPM doesn't change and you can't feel it while driving...

Hi all, I've been getting different info from various sources. I have a '94 Ranger with 14" rims. I'm looking to upgrade to the P71 16" (police rims) from a Crown Victoria/Grand Marquis etc. I would settle for a set of stock black steel 16" wheels, But are they all the same? I recall Mopar...

Hopefully an easy question to answer.. I need to know what is the size of the fuel line going from filter to motor. Thanks in advance..

I am in search of the fuel line(s) from (not including) the fuel rail to the filter. I would prefer the stock lines, but if I cant find 'em I'll go with the repair kit. Anyone have a stock pair of lines they're willing to part with? All I can find is a repair kit from Dorman, I don't know what...

Does anyone know if a stock 1994 instrument cluster without tach can be swapped out for one with a tach? Just plug and play or will I need to do some wiring ?

Got a '94 Ranger, My antenna broke off at the base, I drilled it and attempted using an ez out on what was left but that broke off too. So how do I remove the old base? Can't find access to it being under the front cowl. Probably something simple... but I'm just here scratching my head. Thabks...

I have a 94 Ranger with a 5sp manual trans. I recently repaired a leak and was just curious if there is a vent on the trans. I don't want to risk blowing out a seal or the like. Thanks in advance.

To make a long story short, I have a leak and I think I fixed it. Now the problem. It's just a stock 5sp in my 94 ranger 4 banger. I pulled the shifter out of the top of the trans and cannot get it back in so that it works. It goes in place but wont shift into gears. I don't believe it was...

I have a 94 Ranger XL and would like to know if the wiper control is located under the dash or is it all controlled up in the column? I think I found a box that clicks when wipers are turned on but don't want to go through the hassle of removing it if it's not the part. If it is does anyone...

I'll start with I have a 94XL 2.3 Ranger. Saturday I noticed my heater blower motor wasn't working so I checked the connection and it still didn't work, so it was time to check fuses all ok. So I pulled apart my dash to get to the heater control. Everything checked out good there too! So I...

Happy new year all! I have a rough idle in my '94 2.3L. I did a compression check on it and the #3 cylinder measures about 120 psi, while the other ones are at about 175psi. So that pretty much answers that mystery. The Haynes manual states that low compression on one cylinder while...

I was having a problem with a VERY bad idle. I needed plugs and wires so I went for it. Well, it was better but still missing. I drove it for a day with fresh gas and some fuel treatment. Still was running rough so I started doing diagnostics. Used my EEC-IV code reader and it said nothing...

Ok, I've put 4 of the Teflon(?) seals on my pressure line to pump. The first couple, I tightened way too much. The next one was close but had a small kink in it and leaked a little. I had another new seal so I figured that I'd fix it. I put it on and just snugged it up. It leaks worse than the...

I have a 94 Ranger with the 2.3. I would like to know what size is the stock pipe?